Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

From which function new node will get version detail for the first time in mesh 0

Hi all, I am using ble open mesh with pca10028 boards ble mesh is working fine. I am developing a application that has to blink led in mesh( without any delay between...

2178 views

0 replies

Started over 8 years ago
by Manjunath
Not Answered

low power uart mode leaves TX asserted while CTS is disabled 0

I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...

616 views

0 replies

Started over 8 years ago
by Jim Dattolo
Not Answered
BLE nRF OpenMesh - data rates in typical configurations 0

Hello, I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture. I'm considering using it in a network consisting...
1377 views

0 replies

Started over 8 years ago
by piorossi
Not Answered
Is it useful to simulate my PCB design using CST Studio?and How? 0

Hello Nordic Community, I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
1953 views

0 replies

Started over 8 years ago
by mahmoud.tolba
Not Answered
registering to listen ble_ancs_c events 0

Hi. I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
- nrf52 s132 ble ancs sdk v11
791 views

0 replies

Started over 8 years ago
by Matts

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Peripherals And RF Test: Writing device drivers for UART peripherals

Halvor Bjorstad

This post aims to cover some of the specifics of developing device drivers for UART peripherals for Zephyr.
- 20 Jul 2021
Software: Testing concurrent multi-protocol support of Zigbee & BLE over single USB connection to external CPU

Mark Q

Purpose The purpose of this blog is to showcase how a single USB bus can be used as the physical transport for multiple protocols when an external CPU is the controller. Specifications as tested Boards…
- 13 Jul 2021
Peripherals And RF Test: Working around missing shield labels (on the nRF9160 DK)

Embla Flatlandsmo

Table of Contents Objectives What are device tree overlays, and how do they relate to shields? Why are Arduino nodes not recognized in the nRF9160 DK? The workaround: Using the shield as a board ove…
- 25 Jun 2021
Peripherals And RF Test: LVGL on a TFT LCD Display with the nRF9160 DK

Embla Flatlandsmo

Table of Contents Hardware Components Wiring Software Prerequisites Steps Incorporating this into other projects Further reading Attached files This blog post demonstrates how to get a LVGL sample…
- 25 Jun 2021
Software: Using the NCS / West to program the Radio_Test example into the nRF5340-DK for agency testing.

Jay Tyzzer

Background: There is a need to be able to put a Nordic Semiconductors S0C /transceivers into modes where the physical layer and RF characteristics may be ascertained. The radio test example is used to…
- 18 Jun 2021
Software: Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice - Part 2 Central role

Hung Bui

This is part 2 of the series Building a Bluetooth application on nRF Connect SDK - Contrasting to SoftDevice based Bluetooth applications You can find the other parts here: Part 1 - Peripheral Role. Part…
- 5 May 2021