Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Cannot connect or recover nrd51 dk 0

Hi, I have 3 nRF51 DK pca10028 v1.1.0 I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
- nrfgo studio recover jlink
1358 views

0 replies

Started over 10 years ago
by eozkucur
Not Answered

Power Issue with nRF51822 0

Hi Guys, Thanks for your precious time and insight. Let me try to explain what we did, We have developed a custom board After assembling the board, we do a bare board...

743 views

0 replies

Started over 10 years ago
by deepu
Not Answered
ADXL 345 Tutorial 0

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
- ADXL 345
- spi
- adxl
3215 views

0 replies

Started over 10 years ago
by Milad
Not Answered

Revised spi_master to utilize a mask for cs 0

Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...

1271 views

0 replies

Started over 10 years ago
by nszmnsky
Not Answered
Softdevice Serialization (RPC) for S130 in SDK 9? 0

What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
- s130
- serialization
- rpc
- nrf51422
- nRF51 SDK
621 views

0 replies

Started over 10 years ago
by Catalin

Recent in the DevZone Blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018