Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Supporting multiple network interfaces + devices on one MCU 0

Hello, I'm working with a custom board using an nRF5340 as its primary MCU and NCS 2.7.0. The application I'm developing requires internet connection and can ideally support...
9 views

0 replies

Started 37 minutes ago
by Amira R.
Not Answered
"Toolchains" warnings 0

Hello, Since a few days ago, when I start VS Code, I get the following warning: But when I check the settings in VS Code, v1.x.x is not there. What could be the...
39 views

0 replies

Started 4 hours ago
by KatoTakayuki
Not Answered
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. 0

nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration: CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
31 views

0 replies

Started 5 hours ago
by epolicar
Not Answered
BLE antenna switching on/off while transmitting 0

Hello, We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
- Evaluation
- antenna
- nrf52832
- bluetooth le
- ant
- rf design
- hardware
34 views

0 replies

Started 6 hours ago
by xinyangt
Not Answered
How to software-switch between ESB and BLE on a nrf5340 net-core? 0

Hi, I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
37 views

0 replies

Started 9 hours ago
by nfbe

Recent in Nordic blog

nRF Connect for VS Code

Ali Aljaani

The nRF Connect for Visual Studio Code (VS Code) lets you develop, build, and debug applications based on the nRF Connect SDK using the VS Code Integrated Development Environment (IDE).
- 31 Aug 2021
Optimizing Power on nRF5340 SoC Designs

WesC

Objectives The objective of this blog is to guide the user in the optimization of power on the nRF5340 SoC. The goal is to understand what is needed from a software, hardware, and system level design to…
- 24 Aug 2021
What's new in Bluetooth 5.3?

Ali Aljaani

The Bluetooth Core Specifications v5.3, released mid-July 2021, is the latest version of Bluetooth, the number one short-range wireless protocol. This new version introduces several features enhancements…
- 20 Aug 2021

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019