SDCard with SPI doesn't compile for nerf5340

[warcomeb-am]

Hello,

I am trying to add SDCard management, over SPI bus, into my project with nRF5340. When I try to compile, the error is always the same. I am trying the code over the devkit, while I wait for the final custom board is ready. The error is:

C:\Users\x\ncs\v2.1.0\zephyr\include\zephyr\toolchain\gcc.h:77:36: error: static assertion failed: "Only one of the following peripherals can be enabled: SPI0, SPIM0, SPIS0, TWI0, TWIM0, TWIS0, UARTE0. Check nodes with status \"okay\" in zephyr.dts."

The pro.conf is:

CONFIG_GPIO=y

CONFIG_PRINTK=y

#CONFIG_DISK_DRIVER_SDMMC=y
#CONFIG_SPI=y

CONFIG_LOG=y

CONFIG_FILE_SYSTEM=y
CONFIG_FAT_FILESYSTEM_ELM=y


CONFIG_FS_FATFS_CODEPAGE=850
CONFIG_DISK_ACCESS=y
CONFIG_DISK_DRIVER_SDMMC=y
CONFIG_DISK_DRIVERS=y
CONFIG_DISK_LOG_LEVEL_DBG=y
CONFIG_SDMMC_SUBSYS=y

CONFIG_ASSERT_VERBOSE=y

CONFIG_BOOTLOADER_MCUBOOT=y


CONFIG_MAIN_STACK_SIZE=4096

And the nrf5340dk_nrf5340_cpuapp.overlay is:

&spi0 {
    status = "okay";
    cs-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
    group1 {
        psels = < NRF_PSEL(SPIM_MOSI, 1, 10) >,
               < NRF_PSEL(SPIM_MISO, 1, 11) >,
               < NRF_PSEL(SPIM_SCK, 1, 12)>;
    };


    sdhc-spi-slot@0 {
            compatible = "zephyr,sdhc-spi-slot";
            reg = <0>;
            status = "okay";
            label = "sdhc0";

            
            mmc {
                compatible = "zephyr,sdmmc-disk";
                status = "okay";   
            };
            
            spi-max-frequency = <4000000>;
    };
};

I don't know what is the correct way to solve the issue!

I am using the SDK 2.1.0 over Win10.

Thanks

Marco

[warcomeb-am]

Hello, sorry, I think it was related to the current issue.

Anyway, I'll open a new case.

Thanks

Marco

[warcomeb-am]

Hello,

I added this line:

&uart0 {
    status = "disabled";
};

Now the error is different:

In file included from C:\Users\warcomeb\ncs\v2.1.0\zephyr\include\zephyr\toolchain.h:50,
                 from C:\Users\warcomeb\ncs\v2.1.0\zephyr\include\zephyr\init.h:10,
                 from C:\Users\warcomeb\ncs\v2.1.0\zephyr\include\zephyr\device.h:29,
                 from C:\Users\warcomeb\ncs\v2.1.0\zephyr\include\zephyr\drivers\spi.h:24,
                 from C:\Users\warcomeb\ncs\v2.1.0\zephyr\drivers\spi\spi_nrfx_spim.c:7:
C:\Users\warcomeb\ncs\v2.1.0\zephyr\include\zephyr\toolchain\gcc.h:77:36: error: static assertion failed: "/soc/peripheral@50000000/spi@8000 defined without required pin configuration"
   77 | #define BUILD_ASSERT(EXPR, MSG...) _Static_assert(EXPR, "" MSG)

Thanks

Marco

[Kazi Afroza Sultana]

have you defined pin number of spi0 node?

[warcomeb-am]

This is my overlay file:

&spi0 {
    status = "okay";
    cs-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
    group1 {
        psels = < NRF_PSEL(SPIM_MOSI, 1, 10) >,
               < NRF_PSEL(SPIM_MISO, 1, 11) >,
               < NRF_PSEL(SPIM_SCK, 1, 12)>;
    };


    sdhc-spi-slot@0 {
            compatible = "zephyr,sdhc-spi-slot";
            reg = <0>;
            status = "okay";
            label = "sdhc0";

            
            mmc {
                compatible = "zephyr,sdmmc-disk";
                status = "okay";   
            };
            
            spi-max-frequency = <4000000>;
    };
};

row 4 to 8, right?

[Kazi Afroza Sultana]

You need add pinctrl nodes.

Here is an example from zephyr board b15340 how to add pin control (C:\NCS\v2.1.2\zephyr\boards\arm\bl5340_dvk)

''

&spi3 {
compatible = "nordic,nrf-spim";
status = "okay";
cs-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;

pinctrl-0 = <&spi3_default>;
pinctrl-1 = <&spi3_sleep>;
pinctrl-names = "default", "sleep";
sdhc0: sdhc@0 {
reg = <0>;
compatible = "zephyr,sdhc-spi-slot";
status = "okay";
spi-max-frequency = <8000000>;
mmc {
compatible = "zephyr,sdmmc-disk";
status = "okay";
};
};

};