I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I am researching OTA procedures and I spent more than a few minutes wrestling with flashing soft devices and bootloader code to the nRF52_DK.
What I found is JLINK seems...
When adding extra buttons on breadboard for NRF52-DK do we need to use resistors OR i can directly connect one leg to GPIO pin i.e 30 and another to gnd.
I'm trying to use the nRF24LU1P as a standalone 8051 with the nRF24 radio inside. I provide 5v on the USB connection but no host connection. I am trying to operate in PRX...
Hello,
I'm using the nRF52840 development kit with the "« ble_app_att_mtu_throughput" example with version s140 6.0.0-6alpha.
What's the bitrate used in the long range...
I'm using nrf52832 in my peripheral device, I want to secure its connection via any authentication is there any method for that?, also I need to encrypt its data(characteristics...
Hello,
I'm working on a bootloader based on the examples in SDK 13.1. As we have expanded its functionality, I'm now wondering what happens when one of the steps in the...
Okay this got us going around in circles and it looks stupidly simple. It seems there is a knowledge gap since we saw many posts similar to ours but without clarity as of...
Hi,
I am getting data over thread and BLE network. I want to send the received data over uart.
Is it possible to use serial example to merge with thread server example?...
Hi,
We are having problems trying to integrate support for maintaining application context and bonding info across firmware OTA updates on our NRF52 (nRF52832) based board...
I just test nRF52840 DK with ble_app_att_mtu_throughput_pca10040_s132 example. I know BOARD_TESTER transmits 1024 dummy kbytes to BOARD_DUMMY. I want to replace dummy byte...
I am working with the throughput example for the nRF52840 demo board.
I have found all sorts of control structures which include the counts of bytes sent.
I have not found...
Hello,
I'm developing a nRF52810 application with the nrf52 Development Kit (for nRF52832), SDK v14.1.0 and Softdevice s112_nrf52810_5.1.0-2.
I'm working with Segger...
I am having a problem when trying to configure a node with at client model to my Bluetooth Mesh network.
When calling access_model_reliable_publish() , NRF_ERROR_INVALID_PARAM...
I am working in sdk14.1 nrf52832 ble_app_hids_keyboard_pca10040_s132.
I have successfully implemented a keyboard + Consumer control command in the HID service.
It works...
When I only used XXLARGE block, I got bellow error:
..\..\..\..\..\..\components\libraries\mem_manager\mem_manager.c(484): error: #94-D: the size of an array must be greater...
