Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi, I am a beginner programmer and I have the next problem.
I am working with nRF52832 SDK 12.2 trying to send AT commands to an ESP8266. I send the AT commands byte by...
Hi all
According to errata 146 of the nRF52832 Rev 1 errata sheet V1.5, the LFRC oscillator has a frequency tolerance of 500ppm instead of 250ppm.
What are the consequences...
I have a bootloader compiled from SDK 14.0, and when I try to upgrade to 14.1, the new linker script (secure_dfu_ble_gcc_nrf52.ld) does not contain the UICR_BOOTLOADER memory...
Hi,
I'm using the nrf51822 and I want to merge Server and Client roles in one Peripheral device. I am already able to send a history of temperature and humidity measurements...
Sometimes when the method RequestData is called after receiving a notify on the characteristic, the Master Emulator seems to hang for a set amount of time before throwing...
Hi guys,
I have troubles with MCP 3.10.0.14 but the device (PCA10031) cannot be detected in my laptop (Win 7 enterprise). I actually checked it on other PCs and everything...
Hi, I have just taken on responsibility for maintaining some firmware written for the nRF24LE1. One file, radio.c, contains the copyright header:
/* Copyright (c) 2008...
Can a proxy node also be a client and server node (a controller node)?
What are the key differences between a server and a client in BLE mesh?
Can a server relay a packet...
Hi,
When I try to download code to my nRF52832 from Keil with the example "BLE ATT_MTU Throughput Example", I get this error: Error: Flash Download failed - "Cortex-M4...
i want make delay funtion by timer?
in the other MCU like PIC, AVR, stm. i find register that hold value counter and i cant set this value
for example:
timer 8 bit will...
Hello
Just to confirm:
is it OK to use 2-layer PCB with nRF52840?
In case a 4-layer is needed, when do you advise the use of a 4-layer pcb?
Basically we...
I am trying to build the project which I downloaded from github for the "A beginner's tutorial: Advertising" but I get errors for missing files when I try to build it both...
How the ble peripheral knows that ble central was disconnected?
if i trying to send continuously some packets to ble peripheral some times peripheral is not responding?
...
Hello, everyone~
As the title, is there a complete tutorial for that? I even don't know if I can download the project directly without flashing SoftDevice additionally...
Dear Nordic Devzone,
Just recently I purchased 2 additional nRF52840. In total I have 6 of them now;
The first four all have the following numbers on the chip:
pca10056...
