This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hello,
I am working with the nRF-SDK-for-Mesh v0.10.1 I am able to compile and run everything fine. However the DFU example hangs. It looks like a hard fault ( all the...
Dear friends,
As shown in the pic below, my nRF connect won't start. Automatic firmware detection and programming are done.
nRF Connect: v2.2.1, board: PCA10040 AND PCA10036...
When i klick "Erase all" in nRFgo Studio, i allways get this Message
"unable to find or open JLinkARM.dll"
i did already try several hints from this site.
corrected...
Hello,
I will post this question to NDZ first time .
Our customer is in trouble to reduce power consumption at nRF52832.
Our enviornment is below.
CPU: nRF52832...
I am using the ble_app_uart example as my base on a 52840 with sdk 14.1. I have commented out BLE_ADV_EVT_IDLE case in on_adv_evt() function and the BSP_EVENT_SLEEP case in...
Hi:
I download the google official example "android-BluetoothLeGatt" from github
In the original code, the SDK26 is used, but it can not find any BLE device.
If the...
hi, i'm newbee in BLE,now i have a trouble about advertising in NRF51822.
in my project,after BLE disconnect, I can't see BLE again that mean BLE can't advertising continuously...
Is there a good Mac log analyzer for Android's btsnoop_HCI.log file?
I'm trying to debug an Error 0x81 (GATT_INTERNAL_ERROR) that is being returned when I try to write...
Hi, all!
Sorry, I'm not good at English myself.
My device is nrf52832.
Example code is ble_app_uart (pca10040, s132), I did not modify the code.
My problem.
Ble...
I'm working on a custom board based on the nRF52832. I'm developing on Win 8.1 using SES and a J-Link Plus. SDK version 14.1.
I'm trying to follow this tutorial here devzone...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
I am planning to use MDBT42Q with Chip/Ceramic antenna. I can see in the data sheet they have mentioned an optional 32.768khz crystal.
see page 32 (8. Reference Circuit...
