We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi,
I'm using nRF51822 with SD130 (SDK 12.1).
I had a firmware based on mbed that had RSSI update, and it was getting quite a few updates per second.
I've now gotten...
SensirionHumiditySensorsSHT3x.pdf
I'm using a Sensirion sensor (see attached datasheet). I'm running SDK 12.2 and SD132. I've set up the TWI to be a master, and I'm using...
Hello !
I'm looking to combine the softdevice into my .hex file generated by Keil.
Currently, when I compile my project, Keil gives me a .hex. To implement this hex file...
Hello, I received my thingy52 and wanted just temperature ...
I see that thingy is not using ESS - environmental sensing service so I tried to create my own.
(I tried to...
(Building with nRF5 12.2.0 / armgcc)
I want to do bursts of pulses using PWM for the pulses and a TIMER to enable the bursts.
I need this to be non-blocking so I can also...
I am interfacing nRF52832 to run ANT protocol in a custom board. Can I use the nRF52832 to broadcast the data received through the UART port without programming the device...
Hi Team,
We are using board PCA10040 wtih nRF52832 SDK 11.
We got nRF5_SDK_11.0.0_freertos_dfu_060516.zip Production SDK which is working fine for me.
I am using project...
Hi folks,
Currently I am able to do secure OTA DFU on my nrf51822 chip (MDBT40) using the example code provided by Nordic SDK 12 (s130). It works charming!
However...
i cannot able to find the example code in the examples of nrf52 SDK 13.0, am a beginner to this great platform , can anyone please help me for the above problem
Having great difficulty install Python and pip just to generate the keys for secure DFU. This seems like a greatly complex requirement just to be able to use this module....
Currently using nordic52832 to develop products that use batteries.
We found that the problem is that when the BLE module is connected successfully, it takes 200ms to send...
Hi all!
I am developing an nRF52 application that uses RTC interrupt to measure an ADC value every 100 ms. Depending on the measured value the chip shall either go back...
I am using nRF 52 development board. Using Keil to program it. Its has 4 buttons. We can easily detect when a button is pressed, but is there a way to know for how much time...
I'm using the following code to make the beacon sleep:
static void on_ble_evt(ble_evt_t * p_ble_evt)
{
uint32_t err_code;
switch (p_ble_evt->header.evt_id)
{
case...
