I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi I am using gcc based environment for flashing the nrf52840 SDK with BLE applications. I tried to modify one of the applications to send SPI data received from non-nordic...
I am using sdk12.3 with NRF51822 and the original ANCS project. It can successfully bond with iPhone ,but the bonding only takes place at the first time after the firmware...
Hi, I am currently trying to receive a characteristic notification using an Android device which is connected to a ble beacon with the nRF52832 microcontroller. It works fine...
I am trying to pass data to a central device by updating a characteristic. I am calling the function sd_ble_gatts_hvx(m_bcs->conn_handle, &hvx_params) after passing a hvx_params...
NRF52 DK - SDK13.0 - ARMGCC - Eclipse
I am trying to add a custom service to the example ble_app_hrs.
I add all the part per the tutorial and end up getting error 7...
Hi.
I am working on a project which is using SPI and BLE together.
I wrote SPI code before without soft device. It has simple update function which is sending SPI data...
Hi
I did a bunch of boards for a product, and in the latest version I used a BQ25121 PMIC which also has a reset output which I tied to the nRF52 input. On the previous...
Hi all,
There are lots of posts on the devzone about adding DFU service to a custom application and they have been very helpful in getting to this point.
At this point...
I was looking into changing the S130 attribute table size, which is by default set to BLE_GATTS_ATTR_TAB_SIZE_DEFAULT, and noticed that this default seems to be set to zero...
Hi,
I have programmed my nRF52 DK using the ble_app_beacon example from SDK 14 along with S132 V5. I have set NON_CONNECTABLE_ADV_INTERVAL to 3000. I was expecting to see...
Greetings,
I am interfacing AT24C01A(EEPROM) with nRF52 ,SDK11,PCA10040.
For writing to the EEPROM and reading data fromn EEPROM, I am using the following code,
I have...
Hi, when reading the BLE Mesh example code, I got really bewildered by this function:
access_model_add
and inside, there is this gem:
element_has_model_id
...
What's the expected behavior when reading a register that is write only? For example, I'm using an some code that is reading the value of the TASK_START register of the RNG...
