Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Environment
nRF52832, nRF5x-Command-Line-Tools_9_7_1_Linux-x86_64,
Problem:
Programming of Softdevice, Application and Bootloader with nRFGo Studio works.
Programming...
Hello,
As I understand it, bluetooth declaration IDs can be used for multiple products as long as the products all share the same QDID . In other words, If you do it right...
I have been following the tutorial devzone.nordicsemi.com/.../ on how to use eclipse but in the makefile part im getting this error. I'm using sdk v11. I have used sdk v14...
hi,
i doing a program to receive multiple service data from nrf thingy 52 to nrf52840 central device.
as of now i have implemented weather service, motion service and...
I have been trying to integrate support for multiperipherals into my application, but am continuing to get errors when attempting to start advertising after the first connection...
As I don't know much about audio,I have trouble with the gain of the pdm module in nrf52832.Now
I have used MP45DT02 as the digital microphone,but I just can't understand...
Hi, I've searched and googled through this site and made sure no one asked this question before.
In core\Bearer_event.c, there is this function:
bearer_event_flag_t...
I'm trying to connect two nRF5 devices together, Central and Peripheral, and use a custom BLE service that I have written that has a custom 128 bit UUID.
I'm in the process...
Hi,
We are sending a data using Nordic UART Service (NUS), the data is transferred over BLE as a Indication.
From Message Sequence Chart in Nordic Infocenter
Here...
I am researching OTA procedures and I spent more than a few minutes wrestling with flashing soft devices and bootloader code to the nRF52_DK.
What I found is JLINK seems...
When adding extra buttons on breadboard for NRF52-DK do we need to use resistors OR i can directly connect one leg to GPIO pin i.e 30 and another to gnd.
I'm trying to use the nRF24LU1P as a standalone 8051 with the nRF24 radio inside. I provide 5v on the USB connection but no host connection. I am trying to operate in PRX...
Hello,
I'm using the nRF52840 development kit with the "« ble_app_att_mtu_throughput" example with version s140 6.0.0-6alpha.
What's the bitrate used in the long range...
I'm using nrf52832 in my peripheral device, I want to secure its connection via any authentication is there any method for that?, also I need to encrypt its data(characteristics...
Hello,
I'm working on a bootloader based on the examples in SDK 13.1. As we have expanded its functionality, I'm now wondering what happens when one of the steps in the...
