I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello everyone, I've been trying to solve this problem for several days.
Hello everyone, I've been trying to solve this problem for several days.
I have developed a custom...
Hello!
I make peripherial device with some custom services. It is connecting with smartphone. i need secure access with it with passkey (pin code).
My last result is when...
I have one Service UUID and its only two characteristics UUID which is Tx (App to BLE) and Rx(BLE device to APP) to get different type of data e.g. Heart rate, Sleep data...
Thanks for your help עוטד. I want to use BLE / beacon technology in order to track items that pass-by in high-speed and close proximity (0.5m). This means I only have a few...
Hi,
I am using ble_app_hrs_c as the base for central. I have included 5 characteristics in the peripheral and central side. How to make ble_nus_c_rx_notif_enable() to notify...
ble_gap.h Hi,
At the moment, when a link loss is detected (in a connected mode), it takes around 3 seconds for it to be identified (with DISCONNECTED event). Is there a way...
Hi,
We are using system-off mode to save power in our device which uses nrf51822 chip. Our application requires regular wake-ups using RTC interrupts.
But the wake up...
Hello!
I know that nrf51822 beacon advertising packet consists of the following seven data fields:
Vendor ID
Service
Data payload size in bytes
UUID – manufacturer...
I would like to develop a BLE keyboard using nRF52832.
If you know the example source code, please let me know.
And can USB BLE Dongle for Desk-Top PC use the following...
Hi team,
I am trying to figure out how mesh network works. I do experiment with nrf52832 develop board and nrf5_SDK_for_Mesh_v0.9.2-Alpha. After I flashed light_control_server...
I have an app that requires BLE stack to be re-initialized, however it seems that if you run
ble_dfu_init();
more than once, it crashes
Upon further inspection...
Hi all,
I'm working with the nRF52 and I'm trying to run the heart rate sensor example from SDK version 13.1.0 using Crossworks as my IDE. I can compile and run the program...
Hi,
The below results indicate the nRF Connect app requires a handshake even when scanning without connecting. Is this true?
I am using the android 'nRF Connnect' app...
Are there any known issues with the nRF USB on the new chip or dev kit? I bought a dev kit to test out the USB functionality, but was unable to get any programs working. No...
