Hello.
I'm trying to control a GoPro camera via ble. Gopro has documentation that describes the available services and chars, as well as the exchange protocol ( https:/...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi, I would like to consult how could I deal with this error and build the code succesfully.
In device.h
'__device_dts_ord_113' undeclared here (not in a function); did...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
I use a NRF52832 with SDK15.3 S332,
#define NRF_SDH_BLE_GAP_DATA_LENGTH 251
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 247
When my device as a periph sending data to the...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
We are able to run both these services (experimental buttonless DFU and experimental app ble blinky) individually in Eclipse GCC, SDK 12. However, when both of the services...
I am intended to integrate the Nordic SoC nRF52832 in our PCB to generate a PWM.
However, I could not understand the difference between the following:
topicSchematic QFAA...
Hi to everyone, i have the mpu6050 code and i have to change it with parameters of adxl345.
i have this definitions:
#define ADDRESS_WHO_AM_I (0x75U) //!< WHO_AM_I register...
Hi, I am trying to connect a peripheral device which in this case is a BLE device called DELTA and I am trying to connect it to a central device which is the NRF52 board....
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
In nRF5_SDK_12.1.0_0d23e2a in file: ...\components\softdevice\common\softdevice_handler\ant_stack_handler_types.h In lines 30-32 inside #ifdef ANT_STACK_SUPPORT_REQD is preprocessor...
Hi ,
I have nRF51822 beacon and J-Link LITE and i am using nRFgo studio setup .I am trying to flash the hex file in to the beacon using nRfgo studio.The beacon has two...
Hello!
The DEC2 pin is connected to an N.C. capacitor C6 in the newest refreance layout and the nRF52 DK layout. So does it mean I can just left it DNC like the 44th pin...
Hi,
I have a custom board of nrf51822 with no external crystal, neither 16 Mhz nor 32Khz. I am trying to use uart and app timers from SDK11 but when I start any app timer...
I'm in a situation similar to the one described in this question:
devzone.nordicsemi.com/.../
The company performing the test ask me to provide a device that can switch...
I wanna execute rtc0 on the project which is inside examples\ble_peripheral\ble_app_uart file in sdk 11
When i write the following codes ,nrf51 is locked.bluetooth connection...
I created a characteristic of 20 byte length in a peripheral.
when peripheral does indication, the length of indication data in central is always 20 byte.
I want to send...
I'm porting from sdk10 to sdk12.1 and changing to .zip based libraries in keil5. I've unzipped the sdk into the directory and the examples work fine. However, if try to copy...
Please find attached the screenshot of the schematic where i have combined the RF circuitry from
the NRF52 DK and the NRF51822 dongle for a compact board development. . ...
Hello,
Can anyone tell me if it possible to have one peripheral device connected to 2 central devices ? I am using S132 softdevice with nRF52832 board.
Thank you !
