I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
I am Planning to Implement Card sniffing with NFC Front Chip !
Can I Utilize Comparator for card presence detection system senses the card by measuring the decay time of...
Hi
The slave select (ss) pin during the spi communication is always low even when i make it high to release the spi bus. It looks to me that I'm not actually controlling...
Hi All,
I got 66uA current consumption in sleep mode and trying to reduce it further to few uA. I have disabled the serial interface and still wondering if there is anyother...
Hello All,
I am working on the nrf52810 module.
I am using sdk 15.3 with softdevice 6.1.1. (IDE segger)
Issue-
1. I am giving the Advertising name as " TEST_01 ...
Hi everyone,
this is my first question in this blog.
I am trying to use the library pc-ble-driver-py in order to interact with a DevKit (in which an example code is implemented...
Hello!
I want to use a long range and buttonless bootloader in nrf52811. S140 cannot be used for this task, because S140 use more then 150KB of flash.
Is it planned to...
I need to download nRF Sniffer v2.x, but the link is not valid, please send me a valid link
Old unavailable address: https://www.nordicsemi.com/Software-and-Tools/Development...
Hello,
I have to send hardcoded AT commands on button press on nRF9160dk. So for that, first I did program for button press. It is working fine. Then I did simple_at program...
Hi,
SDK: nRF5_SDK_00.11.00 ; S132 SoftDevice v2.0.0
I am working now to migrate my application from DM to PM (in order to better handle pairing&bonding).
Sometimes the...
Hi team, there is nRF52840 connected to STM32 via UART, the goal is to receive STM32 firmware over BLE (using nRF52840) and send the firmware to STM32 via UART.
My goal...
Hi!
I am realizing a comunication between a serial device and the nRF52832 through UART; i set PIN 5 for TX and PIN 10 for RX (after set PIN 10 for GPIO use) and i don...
Hi
I am planning to use Zephyr Rtos on a Telit Module (BlueMod-S42) based on the nRf52832 SOC.
As we are making both Client and Server application, the question has 2...
I was using a sample code from here which was posted by Jørgen Holmefjord at the link: https://devzone.nordicsemi.com/f/nordic-q-a/43750/to-display-uuid-major-minor-values...
