Hi everyone,
I'm currently working on measuring the power consumption of the 9160DK board and following the guide: Getting started with current measurements on the nRF9160...
Hello,
I am attempting to build the Matter template using only the nRF54L15’s internal memory. While the build occasionally succeeds, it more often fails, and I am unsure...
Hi,
I'm currently using NCS v2.9.0 under sysbuild and have recently been using board definitions from different directories. My recent projects possess a "boards" sub-directory...
Hi,
a couple of days ago, I had to install some STM plugins for VS Code (I'm sorry ).
In the process, the "CMake Tools" from Microsoft were also installed. I remember...
nRF52840 NCS 3.0.1 MCUBOOT
OTBR on Raspberry Pi 4
I am running the OTBR on a Raspberry Pi 4 with the RCP on a dongle. I am running the coap_client on a nRF52840DK. I have...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I change nothing on the code form the sample, after patching I have succesfully build the code and...
Hello, I wonder if it is possible to run the Thingy91 in MQTT-S with a certificate system to ensure the connection between the broker and the thingy. (CA, device certificate...
Hi all
According nRF51822 Product Specification , GPIO pin can config to SPI interface. Means if I set a specific GOP pin range to SPI and connect these pins with...
I am successfully sending data from the PCA10001 Evaluation Kit to the Master Control Panel. But I cannot find any information about initiating and sending data from the MCP...
Hi,
Here i am attaching my text file. in my case timer api is working
but button event handler is not calling.
Kindly tell me , what is my fault.
Regards
Balaji...
I want to store a block of data in nRF51x22. I tried the following:
void HalStoreNVMBlock(uint32_t size, uint8_t* pBuf)
{
nrf_nvmc_page_erase(NRF_UICR_BASE);
nrf_nvmc_write_bytes...
I'm using the TWI module. Where can I set whether the DSA SCL pins have the internal pull-up enabled or disabled? I can't even find where to see if they are enabled at all...
Hi guys,
I am having a breakout board made and would like to know what are the programmers out there which I can buy which will help me program the board. The J-Link is...
Hi,
I'm designing a custom board equipped with nrf51822 and is not clear for me how the flashing part works; I bought nrf6700 and pca10005 as reference design and now i need...
I am coming across a strange issue with a nRF24L01P running enhanced shockburst. I have 1 PRX and a few PTXs communicating in a star network. The type of PTX determines which...
Here i am attaching text file in which my application not able to call interrupt handler.
Kindly tell me what will be issue.
Regards
Balaji
rtc1_app_timer.txt
I'm trying to figure where the BLE bottlenecks are to figure if I should use BLE or maybe Gazell for my product. I've just started to use the BLE stack, so I guess that there...
hi,
i am working with the nRF51822 development kit and trying to load the sample programs given by the nordic guys, the samples without using BLE is working properly but...
Hello,
While debugging, I found that if there was an active BLE connection, the chip would reset when I switch to single step mode, is there a way to avoid this from happening...
From the log:
[23:41:27.2] EnableServices({11:2,16:2,22:2,28:1,})
I suggest that you use hex for the handles - this is what you use upon inspection and other log statements...
I'm currently trying to learn the functions of the softdevice by using the HTS example. I've managed to make an additional temparature service (named custom), which almost...
