I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I'm working on a program which sends 20 kb of data (sending 16 byte at a time) with one condition which is that indication should be enabled first. the first function checks...
Hi. i use SDK 9.0.0 and S130_1.0.0.
I want to recieve data from My peripheral S110..
First, I try to recieve data using example "ble_app_uart_c_S120-master".
I could...
Conditions in www.nordicsemi.com/.../Why-can-Master-Control-Panel-not-find-my-Master-Emulator-Dongle have been met, ie all components of PCA10031 have installed successfully...
in the answer of this question it said that :
You are also not allowed to send a new
indication until the previous one is
confirmed. This is signaled by the
reception...
I found this: github.com/.../nordic-nrf52832-gcc and tried to add it (and its dependency to the nordic-nrf52832-gcc 0.1.0 target to yotta with no luck. Is there a description...
Is there a maximum consecutive receive time similar to the maximum consecutive transmit time? I am operating in 1 Mb/s ESB mode. I am seeing the Rx get disabled approximately...
I am developing a ble program for the nrf51 DK using mbeds api and it is supposed to send 11 packets (notifications) when written to a specific handle. So far it works, but...
I'm receiveing this error 7 on line error 296. the only APP_ERROR_CHECK on line 296 is hci_slip_rx_buffer_register . this documentation doesn't not give any description of...
HI,EVERYONE,
in the document 'nRF51422_PS_v3.0.pdf' ,Page 167, there is such statement
'The selected analog pin will be acquired by the ADC when it is enabled through...
Hi !
According to application requirement, we need to minimize the RSSI variance of the BLE beacon as small as possible. Our RF team has tried to minimize the 37/38/39...
Hi,
I am trying to bond the nrf51-DK with the android smartphone. I want to display the passkey to the user which would be done using BLE_GAP_IO_DISPLAY_ONLY. After which...
Hi, would there be any drawback in setting TIMER_PPI_CH_START to 11 to maximize the number of free PPI for application. 14->15 should be free to use in timeslot and ppis are...
hi, i am new to embedded system.
I am using SPI interface to collect data from the slave(imu) and transmitted it to nrf52 DK,previously,I just used RTT to show the received...
