I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Dear Sir/Madam,
I have a sensor prototype board using nRF51822 for Bluetooth communication and I am now working on its firmware. I have installed MDK version 5.16 and...
Dear sir,
Sir i am using MDBT42V module. I want to know that whether the SCL & SDA pine are internally pulled high in this module ?
Regards,
Manoj Hiwarkar
Hi,
I have a problem where I am getting NRF_ERROR_RESOURCES errors 2 out of 3 times when sending notifications from my peripheral to my central. I think this is caused because...
I have designed a custom board with a TF325J32K7680 32KHz clock with +-50ppm tolerance, for the 32MHz I am using the CX2016DB32000D0WZRC1 with +-40ppm tolerance.
Simple...
Hi,
Within each example in the NRF5 SDK there are a number of folders including
arm4
arm5_no_packs
armgcc
config
iar
I'm having trouble finding an explanation...
Hello everybody,
I used SDK14.2.0 , S132 .
I keep the data from nus_data in the uint8_t array. Then I am trying to write the array with use fds_write.
My fds_write...
Hi, I would like to add source files to Projects with a reltive path. The reason being that I would like to have my own code in a cloud based directory and code from SDK in...
Dear friend,
To u se the Power Monitor for current profile measurement of nRF52832, I prepare the board by doing both of the steps described below:
(1) Short solder bridge...
Hi There,
I currently using PCA10040 development kit for my project. I tried to merge with \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_blinky\pca10040\s132...
Hi
We have a product with Nordic nRF9E5 coupled to Texas CC1190 amplifier.
We are seeing transients at start and end of TX; worst at end. We appear to be non-compliant...
Hello, we are using SDK 5.2.0, SoftDevice 6.2.1 S110 on the peripheral side and S130 on the central side.
We have implemented a serial data link between the two, the central...
I have made a custom PCB with the nRF52832, following the circuit reference, I used the C3 and L1 for tunning the antenna. Instead of a chip antenna I placed a wire in the...
The NRF_LOG library apparently uses memobj, which uses balloc. I assume that means I need to add some blocks in my sdk_config (i.e., MEMORY_MANAGER_SMALL_BLOCK_COUNT, etc...
Hello Guys,
I have some measurements for the determination of the maximum range and the energy consumption. The experiment is based on the ATT_MTU throughput example, nRF5_SDK_14...
Hi,
We have a BLE peripheral device that is used as a mouse/keyboard (nRF52832 SDK 14.0)
The peripheral pairs with most central devices just fine (including Mac and PC...
