Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I have a question about how to build RSC (Running Speed & Cadence Service) ? especially using mbed compiler because I just found CSC (Cycling Speed & Cadence Service). like...
I am trying to add peer manager to multilink_central example on SDK14.1.0 based on the ble_app_hrs_c example. The code is running on nRF52832 and softdevice S132 5.0.
It...
hi,
I need combine to SAADC with BLE interface. The following is the code I have written. However, I'm unable to transmit information via bluetooth. Can anyone help me with...
Hi,
I have found this link devzone.nordicsemi.com/.../ . It seems you need to change SDK or softDevice to make it work with FreeRTOS. Could you please share more information...
Connecting to J-Link via USB...FAILED: Can not connect to J-Link via USB. I am using the BLE Sniffer 1.0 and when I star the Sniffer I get the error code that my software...
Hey guys,
I'm trying to make the FDS work with BLE and the scheduler.
But something doesn't right when I use the Softdevice and scheduler with the FDS.
Must I register...
Dear all,
I have nRF51 DK and I use mbed CLI to build my application that is simple mbed-os-example-blinky.
Also I have SDK11.0.0 and I built the ble dfu bootloader (...
Hi there
I did an upgrade of the bootloader from SDK 12.2 to SDK 14.2. I am using the nrf52832 chip. It is basically the same as the secure BLE DFU example from the SDK...
Hi everybody,
I was looking for a better way to update a data, like a 32-bit-word, without the need to erase the entire page. Part of this question is already been asked...
I was going through all the supported SDKs for the nrf52840 and in all of them, it is mentioned that the ESB and FreeRTOS support is not there yet. Could someone please let...
Hello, I'm trying to implement a buttonless DFU via ANT for a custom nRF52 board. I've got the 212 v4.02 Softdevice and I'm using the 14.0.0 SDK. I am able to transmit and...
Dear
i want to nrf52832 to collect accelaration sensor data（SPI communication 8MHZ）.
The sensor output datas per 250us,nrf52832 will lost the sensor interupt when 52832...
Good evening. I write a project on nrf51822 in which there are a number of services with a set of characteristics (write and read). I need to limit access to some characteristics...
