Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I am using the sample BLE_gls code provided by Nordic.
I have made the following changes in the code:
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES...
Now I want to store some data above bootloader( the address after bootloader), but every time when I call the function pstorage_init(), the function will defaultly set my...
How to add single 128-bit characteristic uuid. It's not based on service uuid.I have tryed the link text ，It's work,but it's something wrong .
I am working on ios ble midi...
I developed a custom board with nRF51822_xxAA on it, working on low voltage mode.
I can program some basic things on it using Keil uVision 5.15 and a J-link to flash the...
Hi,
I'm trying to use the pstorage on a central device.
An event of BLE_GAP_EVT_ADV_REPORT is called by discovering some ble devices while a central device is scanning...
I have a nrf51-DK, SDK 9.0, S110, dual-bank bootloader that supports both serial and ble protocols, developed using GCC/Eclipse. My application uses the watchdog timer. I...
Hi,
I'm developing an Android application that uses Android DFU Library and I want to set the number of packets that are sent every notification interval to 1. I couldn...
On the BMD200 evaluation kit ( www.rigado.com/.../) using the nrf58001:
--> UART TX (pin P0.09) works - confirmed with logic analyzer and Serial Port Terminal on the PC...
We are operating on nRF51822 QFAC with S130 SD. We have a functionality where the device switches between scanning and advertising. Strangely we have observed that after few...
Hi,
When i read the ble_peripheral sample of the SDK, i have a question below.
If my peripheral is connecting a central, then i use function sd_ble_gap_disconnect() to disconnect...
Hi,
The established time tick source for FreeRTOS is RTC1 via the APP_TIMER module. I am trying to shift the basis of the APP_TIMER from RTC1 to TIMER2, so that I can use...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi,
I have an nRF52 dev board (PCA10040). I have been using this board for measuring current. I am using the Keil tools.
Yesterday I made a change to main.c in the ...
Hello,
I am working on S120 v2.1.0 and SDK 9.0 for central and I am able to connect to my iPad. Now I need the central to delete the bonding information stored using pstorage...
Hi All,
I am wondering if I could upgrade from S110 to S130 over the air.
What I see in the S110 and S130 hex file is that the MBR is different. Not many bytes but it...
