hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
I know that a lot of question exists on that subject, but I can't manage to have an accurate battery measure on [Nordic Beacon device] (battery CR1632 3V) ( www.nordicsemi...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
after reading the nAN-36, I tried to write an application for the nRF51822, with the custom Led Service provided with nAN-36.
I take as a base the Nordic HRM application...
Hello!
I'm using the evaluation kit and i have two questions: firstly, I'm trying to make up a program that allows the communication between two modules, on one side a glucose...
Hi,
I work with Master Control Panel 3.6.0.8331 on x64 Windows 7 and I noticed something weird. When device name of a connectable peripheral device consists of numbers...
Hi!
I'm testing a custom service developed on the nRF51822 development board by using the Master Emulator API in a C# project.
The project is based on the example project...
Hi,
I'm trying to set up Keil uvision to debug my nrf51822 mbed board.
I've exported a uvision zip file from the mbed IDE to test with.
I've installed the following...
I am fairly new to the embedded world and I have my development environment setup and running with the other samples but, I'm interested in the 130 softdevice. I have the...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
i would like to know what the logs mean in MCP log file,.
AS follow:
3563;11:19:08.9590 [480108198][ReadPacketQueueThread] Serial port read: 02-00-20-14-00-10-00-04-00-1D...
Is there any possibility to detect active state on the more than one pin using sense mechanism? GPIOTE_IRQHandler is blocked when it detect active state on the one of the...
Hi,
Is there any reverse polarity mechanism inside the nrf51822 IC?
If externally we don't use it, and user connect power supply in reverse way, what will happen with...
Hi, and thanks for reading this, I'm currently able to power the PCA10005 by sending 3.3v to pin1 of p2, and pin5 of p2 to ground, with this setup I'm able to program the...
