Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello! Sorry for my English)
My situation is next: I have a custom PCB with nRF51822 on it. And radio control application works fine on this PCB. I don't know which of...
Hi everybody, i want to read NFC tags and send them via BLE to iOS app. How can i do that? Can i work with nRF51822 and Elechouse NFC R/W ? www.elechouse.com/.../index.ph...
I'm using SDK 9, I flashed the softdevice 8.00
I compiled the project located in \SDK_9.0.0\examples\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5_no_packs
I flashed...
Hey,
I am trying to use app_timers and nrf_delay_ms together but the system gets stuck almost everytime. I have the following code:
void timer_handler(void *p_context...
We have noticed an issue when using the UART on our nRF51822 (SoftDevice = S130, nRF51_SDK_9.0.0_2e23562). Our Nordic app waits for commands on the UART and processes these...
Hello Everyone
I am trying to configure the two GPIO in High Drive mode 5mA but after compiling the program it does not seems like congifured to High drive Mode because...
Hello, I am designing a system to transmit a mono or stereo audio signal over RF, a few hundred feet, then receive it and reconstruct the audio and listen to it on a speaker...
I am developing a HID keyboard with SDK v6.1, SD v7.3, IC revision 2.
The keyboard is already able to advertise (non-whitelist) and bond with iPhone, and connect/reconnect...
Hello
I want to optimize SPI com as fast I can do:
First I am using the fast spi data rate by SPI_FREQUENCY_FREQUENCY_M8 variable and I want to reduce at first the timing...
As far as i understood it supports 4.2 BLE because using it i'm able to see packets between nRF52 central and peripheral boards (HRM example). Is it so?
Question:
I am confused about who can do (or rather who usually does) whitelisting - the master or the peripheral device?
My findings so far:
I can't find a certain...
Hi,
I have written a windows 8.1 application to connect to my custom nrf51 device. It is used for configuration and is set up without requiring a password (I do not need...
I want to be able to transmit the on-board temperature and battery voltage over a beacon application. The application only needs to transmit periodically similar to an iBeacon...
Dear,
I'm now face problem on button interrupt.
I use 3 buttons for my system.
button 2, 3 is used for boot diagnostics. assigned as below.
bsp_event_to_button_action_assign...