Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hello
we have a projekt with periperal "ble-app-blinky" und central "ble_app_blinky_c".
how to do:
when the "peripheral" battery is below 2.3V
then the led 4 on "central...
I'm trying to regularly change some advertising parameters ( ble_gap_adv_params_t.type ). The only way i can see to do so, is by stopping and starting advertising.
However...
I made a pulse oximeter product with nrf51822AC(base on SDK5.2.0 & S110 6.0.0), and implemented SIG GATT-based profile（PLXP+PLXS). Now we want to do BQB RF PHY testing to...
I have an example combining BLE, UART and SPI in which I use RTT to watch the startup process.
The SoC is nRF52 (BLE Nano2); building with armgcc.
This works ok when JLink...
Hi,
I need to send large data(about 200KB) from android phone to my custom board.
Connected like this :
Android Phone ->(BLE) -> nRF51822 ->(UART) -> Custom board...
Hey everyone,
I'm new to the Nordic/Thingy/Embedded world and was hoping I could get some hand holding to achieve a simple change.
I would like to change the Thingy...
Hi All,
I am working printer project where i will be using two boards , one is nrf51 dongle which acts as client(sends/advertise the data) and another is nrf51422 soc on...
Hello community,
I did a central device which is connecting with 8 slaves and this slaves are sending every time 8 bytes when they are connected. My set up is the following...
I'm trying to create a program that takes a stream of UART data at 115k baud streaming in and sends it over BLE as fast as possible. So far, I've
(1)Verified/ made some...
Dear Nordics,
If I add ble_nus service to buttonless_dfu example , it will reset after ble_dfu_init(). If I set
*p_ble_enable_params->common_enable_params.vs_uuid_count...
I am working on S140 on nRF25840. I am using the ble_app_beacon sample.
I want to set the advertising interval smaller than 100ms while using non-connectable mode. But the...
I am developing a product where I need to read a signal from an SPI ADC and send remotely to a receiver. This will be powered of a coin cell.
I see that the NRF51422 is low...
Hi,
I am trying to program nrf52 (on board ), but I keep getting these error:
$ nrfjprog -f nrf52 --program nrf52832_xxaa.hex --eraseall
ERROR: JLinkARM DLL reported an...
Hi,
I'm trying to connect and discover services of a BLE device equipped with a nrf52832. The device advertises correctly and i can see it on the nrf Connect app on both...
