Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I have used NRF52840 and SDK 13.0.0.
When I have used USB or ESB one by one - all is Ok.
But when they are used together - usb driver goes into an infinite loop here:
...
Hello.
I am developing a project on nRF52832 using SDK 13, in which I need to transfer up to 300 bytes of data from iOS device via my dedicated app (in the background) to...
Hi,
I read in the documentation that one can loop a complex playback. The way I understood, one could load a first sequence (say seq1) and a second sequence (say seq2)...
Hi Nordic Team,
i am working on nrg52 to glow a RGB LED with white and Yellow colours. configured the RGB pins to three different Gpio (A2,A3,A4).
for this i am using...
I have an application where I read a IMU at around 60 - 80 hertz.
How should I configure the S132 so I can send my 14 byte string packet with a constant time interval?...
Good evening (at least here...)
I successfully developed an application with Keil on the Rigado EVAL board with the following steps:
nRFgo Studio -> erase all and...
Hi,
is there a way to make a all in one bootloader image which includes Softdevice and APP in one zip?
And is there an example of the DFU via a Master uC. My setting is...
Hello all,
I am trying to program my custom board using the debug out from the nrf51-DK.
I connect all the needed pins and on the nrfgo select the Segger but when I do...
Hi,
I want know how nrf51822 bootloader finds images type(means weather it is softdevice,bootloader,app) when we pass an image to bootloader for update. And also how bootloader...
There is a list of 3rd party modules at www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules . Will it be updated to include nRF52840 modules?
It appears the nRF51822 Product Spec does not list the current nor power for the radio DISABLED state. The Reference manual description of the state is “No operations are...
Hi everyone,
First post here, so apologies in advance for lowly questions!
I have a Fanstel EV-BC832 dev kit for their BC832 module , which uses the 516K Flash / 64K...
Hi all,
Having a bit of an issue with the SPI manager scheduler. When sending small packets (<4 bytes), I seem to be able to queue as many requests as I want.
However...
I asked the following question, TWI Stuck Bus Recovery , last week and got a great answer which I implemented. I tested my implementation by changing the device addresses...
