Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,all
SDK:8.1.0 51822
S7 Edge（android V7.0）
i use the sumsung S7 Edge and the oppo R9S connect with my device,nRF Connect is often note:
GATT_CONN_TERMINATE_LOCAL_HOST...
for ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0
The preferred RAM,ROM and UUID COUNT is shown below
FLASH (rx) : ORIGIN = 0x0001B000, LENGTH = 0x25000...
Hi All
I am trying to build hex file using eclipse id on Mac. everything looks ok, as it eclipse build file without any error but its not working on nrf52 dk.
before...
Now I’m using nRF51822 with S130 SoftDevice.
There are two kinds of devices which is just for scan(A) – 20EA and both scan and advertising(B) - 2EA.
I found that B just...
Hi,
My question is similar to this devzone.nordicsemi.com/.../ but I can't get it to work.
I am using SEGGER_RTT_WriteString and sprintf for debugging, but I am not able...
Our mobile app is currently running atop of easyble and nordicble.js/Cordova. This library works great on all Apple devices, however, Bonding with Android devices of various...
We have done a custom PCB believing that we could use P0.0 as analog input. Now we kind of found out that we cannot, and will change the PCB design. Given that we already...
Hi, I am using nrf24l01+ tranceiver in a project I am willing to sell. I use modules with external antenna and without it. I need the CE certification of the module. Where...
I have used NRF52840 and SDK 13.0.0.
When I have used USB or ESB one by one - all is Ok.
But when they are used together - usb driver goes into an infinite loop here:
...
Hello.
I am developing a project on nRF52832 using SDK 13, in which I need to transfer up to 300 bytes of data from iOS device via my dedicated app (in the background) to...
Hi,
I read in the documentation that one can loop a complex playback. The way I understood, one could load a first sequence (say seq1) and a second sequence (say seq2)...
Hi Nordic Team,
i am working on nrg52 to glow a RGB LED with white and Yellow colours. configured the RGB pins to three different Gpio (A2,A3,A4).
for this i am using...
I have an application where I read a IMU at around 60 - 80 hertz.
How should I configure the S132 so I can send my 14 byte string packet with a constant time interval?...
Good evening (at least here...)
I successfully developed an application with Keil on the Rigado EVAL board with the following steps:
nRFgo Studio -> erase all and...
Hi,
is there a way to make a all in one bootloader image which includes Softdevice and APP in one zip?
And is there an example of the DFU via a Master uC. My setting is...
