I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
Hi,
I'm trying to get an iOS app to connect to a Nordic BLE device. I'm a firmware guy with little app experience but I have gotten a app to work based off the code presented...
Hi,
Im new to BLE and still trying to wrap my head around things. I am using the both new nRF51 DK and nRF51 Dongle for testing at the moment. I know that the old dongle...
I would like to have track time of the day in my peripheral (s110)application. I understood that RTC0 is used by Soft device. RTC1 is used by app_timer application. I have...
hi nordic:
thank you for your great support!
question 1:
App: LightBlue in iOS.
when app scanning for perpherals ,i have found my device,show as "measurement…."
THEN...
Hi all,
I had a working TWI connection combined with BLE advertising. When
I added uart code for printing to putty this TWI connection was no longer functional.
So...
Hello,
I am currently working on a project and I would like to add some security to my device by preventing services from being discovered. Ideally when a user connects...
Hi
I am trying to use the internal ADC to capture an analog value every second. For this I use a timer to wake up every second, start the ADC and go back to sleep.
I...
Is anyone using the third-party BLE module from Taiyo Yuden? If so, where did you find the recommended footprint?
Taiyo Yuden's website only gives very limited information...
In the SDK 8.0 are only examples for nRF51422.
Is it possible to compile this for nRF51822 and is the softdevice 8.0.0 for both controllers?
Best regards,
Roman.
Hello,
i am new to nRF Bluetooth.
My Setup ist:
One Atmel atmega640 and one nrf51822 communication via UART (at the moment).
I am sending data from atmega640 to...
Hi,
I'm writing a bootloader for nrf51822 to be able to update the nRF51's firmware through SPI (data transferred via an STM32 retrieving the file through USB).
My idea...
Hello,
I am trying to write data to flash with the pstorage api. I managed successful to write data to flash with the pstorage_test_store_and_update() function from the...
Hi
Recently we bought NRF51 DK board. Initially when i connect the nrf51 DK board to PC via USB it mounts JLINK driver and on IF/BOOT button it mounts BOOTLOADER drive...
For my application I need to identify the peripheral source advertising packets are coming from. How is this best done with BLE and SDK 7.1? I would prefer not to set a a...
Hello
I have a nrf51822 mbed kit PCA 10024 V1.0.0. When I connect the kit to the PC (Windows 7 64 bits) the Mkit enumerates as an MSD named MBED:
I updated the firmware...
