the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Here is my question.
I always disable uart after I send data.
NRF_UART0->TASKS_STOPTX = 1;
NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
this was write in the...
Is there a compiler/makefile flag that allows for 64bit printing?
I have included inttypes.h, and tried both %llu and "PRI64" as shown:
char scrbuf[30];
uint64_t time_alive...
Hi
We are using NRF52 and SDK 11 and S132.
The nrf52 acts as a central and selectively connects to the closest phones (ios) that are acting as a pheripheral.
For this...
hello,
nordic's engineers, need your help.
(1) the first problem : can not set VDD output to 3.3V
From nRF52840_Product_Specification_v0.5, it says:
High voltage mode...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Hi. I'm using nRF51822, SDK12.2.0, S130 v2.0.1.
I'm using nRF chip as Multi-connection Central and 1 Peripheral as well.
My event function is
static void on_ble_evt...
I've tried everything I can find on this topic and I still cannot get P0.09 to behave as a GPIO pin. Does it have something to do with the way I'm attempting to initialize...
Hello,
I am working on a custom PCB with a nRF52832 and I've been unable to get the ON IDLE power under 480uA. Here are the basics regarding the setup
nRF52832 Rev...
Hello! I'd like to know if S132 v3 implements the frequency hopping scheme defined by BLE.
I've read some documentation on Gazell, but from what I understood, that is a...
Whenever our battery runs to zero, or if we have a reset due to voltage droop, the unit will not auto-connect and the user is forced to "forget" the device in iOS bluetooth...
Hello,
i'm trying to use nRF UART driver (nrf_drv_uart) to implement a high level UART manager.
I followed indications on SDK documentation but it doesn't work and i think...
Working on a project to set up a bidirectional UART to SPI link over ESB with nRF52832 (PCA10040), using SDK 13.0.
Working from provided examples for PTX and PRX, I manage...
Hello,
I've implemented one custom service very similar with NUS. I have two peripherical devices that are running in two PCA10040 with S132 12.1, and one central device...
