I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
ble_app_uart_c2.rar
I want to connect two PCA10001's together, one with the ble_app_uart for s120 using sdk 8, and one with the experimental_ble_app_uart for s110 using...
There's no question, I'm just posting this here in the hopes that it helps someone else out.
After I upgraded my Keil packs to the newest SDK (v8.1.0), my OTA FWU bootloader...
I have a problem getting both mesh and persistent storage to work. I am using the code from github.com/.../nRF51-ble-bcast-mesh and followed the document integrating_w_SD_apps...
Hi,
I am using
HW: nRF6310 + PCA10005
SW: s120_nrf51822_1.0.0_softdevice.hex + ble_app_multilink_central (\Keil\ARM\Device\Nordic\nrf51822\Board\nrf6310\s120\experimental...
Hello,
I am a newbie in in using BLE and exploring the nrf8001 DK. I was able to flash PCA 10000 module with updated firmware and it was detected in the master control...
Hi,
I want to read data ,wich is sent from beacon ,using usb dongle,and after this ,I want to send data received from beacon to pc through serial port.
Exist any example...
Hey.
I am wondering if there is a way to disconnect a slave from a master based on the strength on the connection and not when they naturally loose connection.
To give...
How do I block Bluetooth signals ? (I want the signals to be transmitted 180 degrees, not 360 degrees)
I have read it could be done with aluminium foil, but I have not...
I am looking at using an nRF51 in a BLE product (industrial applications).
One of the things that I have to sort of prove is that it will be a better choice than something...
Hi, everyone. I would like to be notified about the brown-out on my device. I know about POF peripheral, but lowest possible threshold is NRF_POWER_THRESHOLD_V21 (which is...
First off, forgive me for being a newbie at ARM programming in general. In AVR this was straight forward.
I have a circuit connected like this to the ADC (P0.01 = AnalogInput2...
Hi,
I would like to transfer real time ecg data from a 3-channel adc (250 Hz per channel, 16 bits ) using nRF51822 to an android device. I would like to know if this is possible...
