I have a custom board with nRF52840. It draws power over USB and the data lines are connected as well
USB is defined as follows in the dts
cdc_acm_uart0: cdc_acm_uart0...
Im tring to generate sbom in html or spdx format yousing west ncs-sbom -d build i got this error: package.name += '-' + package.version TypeError: unsupported operand type...
Hi there, I'm facing difficulties configuring the Adafruit ILI9341 with the nRF52840. Are there any beginner-friendly instructions on how to configure and program it over...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
Attached is the schematic of my part configured for low voltage mode.
Very close to page 62 in the nRF51822 product specification document.
I am externally feeding 1.8V...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
We start to migrate our equipment from nrf14L01 receiver to nrf51422 receiver in order to serve more equipment.
I am using nrf51822 to receive propietary protocols from heart...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
hi Ole Morten:
thank you for your great support.
i have tested nrf6310\temperature_example. at 30(Celsius)
I checked the data. NRF_TEMP=0x000002AF; TEMP=0xFFFFFFAC;...
Hi,
I need help on calculating the current consumption of our device when it is in advertise mode. So please answer the below questions.
What are all the significant...
Hello,
i would like to use HRM, HID, BAS and DIS profiles simultaniously. I used HID mouse example. I append required HRM things and it work almost properly. Problem is fault...
Hi, I'm a beginner. I want to add to example of the proximity, next service identical to battery service. I need to send 1 byte of data.
Everything works well until when...
I have an application that reads an nRF51822 pin configured as analog input and then sends that value using "ble uart" (included in Nordic's sdk). Analog input is read in...
Been studying the S110 5.x -> 6.0 migration docs. Are there any project-specifics / include-paths / Keil build-settings that must be updated as well?
Do I understand it...
Im stuck that i can't get my Motherboards to update. Just goes into an endless loop of saying toggle power to rest it, starting boo loader, Couldn't start.. etc etc..
Attached...
I have a nRF51822 device which has softdevice and bootloader.
And I'm trying upload my app with following steps:
make .bin file with gcc
Push the DFU button, and...
I'm running a custom nrf8001 board and the nrf8001 is consuming approx 6.2mA on it's own in advertisement mode using the uart demo. Has anyone had this same problem? Any advice...
Flash write and erase works fine, if ble is not initialized( ble_stack_init()).
Once ble is initialized, any write to NRF_NVMC->CONFIG hangs the system.
Do I need to...
