Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Having gotten through the hurdles of getting my IAR project to compile and run on Segger Embedded Studio, I am now seeing different behavior between the two IDEs while debugging...
Hello,
In my application (based on app_nus_uart example, with two NRF52832 boards), one of the cases is uploading/downloading files with sizes up to 10MBytes.
In my app...
Can someone explain the reasons/benefits of using the single vs dual bank BLE boot loader?
Actually, why isn't there a single bank BLE bootloader in the example project...
I have following code which should start the app_timer and blink the LED_1.
When flashed, the LED_0 turns on and I can see the "Started." log. But the LED_1 is not blinking...
Hello,
I use nrfutil to generate the dfu .zip file, the error log is listed below. what is the reason? the softdevice is s140. thanks.
>>nrfutil pkg generate --hw-version...
ble_app_uart_c_pca10056_s140 fails with an assertion - I have downloaded nRF5_SDK_14.2.0_17b948a. For the example project examples\ble_central\ble_app_uart_c\pca10056\s140...
Hi,
I am trying to write a 120 byte data through ble to raspberrypi from my android app(I increased the MTU to the required limit). But all I am able to transfer is first...
Hi Team
Let's assume, we have a provisioner (client) and several successfully provisioned servers in a mesh network. We now want to remove one of these servers from that...
Hello,
I am currently migrating from SDK12.2 with softdevice S132 V3 to SDK14 with softdevice S132 V5 and have a problem configuring device names larger than BLE_GAP_DEVNAME_DEFAULT_LEN...
I am using nrf52832_xxaa and I'm porting my device from SDK11 to 14.
I have found that new sections have been added in the linker file of the examples like sdh_soc_observers...
Hi,
I use SDK v13.0.0 with SD S132 and to debug my application I use UART0 on Putty.
When I use SPIS (0) (no BLE and no softdevice) alone I perform all functionalities...
hello：
i use timer1 to get a pwm waveform，when i use RTT to test it，the waveform is ok，but when i take out the RTT，and Remove the battery and put on the battery again to...
I've made a custom board with nrf51422-QFAC, which I can program with nrf51-DK. I'm using SDK 12.3.0 and SD130, which is flashed to the custom board.
When I program the...
