I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
I'm using SDK11 and PCA10028.
hrs works well, but did not bond with central(both android(kitkat) phone and iphone) in the nRF Toolbox app, althogh it's device manager ported...
I was wondering if anyone has done any extremely high speed UART work on the nRF51 (or the non-EasyDMA module on the nRF52). I need to improve performance for an existing...
Hi,
I ran the ble central example code on nrf51822 16KB ram version without any problem. But when I run the same code in nrf51822 32KB version, the program flow goes to 0xFFFFFFFE...
Working on my first project in mbed using the Nordic nrf51-dk.
The project utilises a TMP112 temperature sensor and attaches the reading to the service data to make it...
I'm trying to rename my device using s130, but the name doesn't get applied.
I went back to the "roots", ie the HRS sample.
Just before entering the loop, I add a name...
Hello,
I am working on a custom board with NRF52832-QFAA-R7 and trying to run ble_app_uart_c on it. I am using uVision 5.23.0.0
The first trouble that I am facing...
I'm trying to implement usb function on the nrf52840. The moment that I connect the usb to the computer the chip resets.
With gdb debugger i found out where the fault happens...
I have some question about ANCS ,when we trun off the IPhone and turn on the IPHONE.
The notifcation is disabled. I have to turn OFF the bluetooth and ON bluetooth form ISO...
Hi All,
I am a beginner,Can you please explain me what is the role of this line?
APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, m_tx_buf, m_length, m_rx_buf, m_length))...
Hi All,
I am using nrf51422, SDK 12.0.0, an SPI OLED display 128x32, and an SD card.
I want to interface an OLED display and an SD card onto the nrf51422. Although my...
Hi all,
I like build a smartwatch-like device that can receive notifications from my android phone. The bluetooth device has a oled screen and displays what notification...
I need to turn on and off one pin around every 100 us. Time between must be 1 cycle (couple of ns) and can't be interrupted at any circumstances.
Without a softdevice I disable...
Hi All,
I am a beginner in nrf52.
I need to get the client device address in ble_app_hrs_central, because I have more than one devices connected.
There is a hrs_c_evt_handler...
After spending half a day on this solution, I found out it wasn't really a solution - it devolved back to the same issue after trying to connect - please advise!
Description...
