I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
We have problem that after deleting bonding info on the NRF51822 the iOS APP doesn't know its bonding info have been removed and try-s to connect whitout asking for pairing...
Several different copies of the dev kit, and a couple of different hosts. I often get "Failed to secure connection. Disconnecting.". I can find where it's generated in the...
Hi Team
For security reasons, I would like the provisioner to stop further provisioning after the network is set up. SERVER_COUNT is usually not reached, since the number...
I am confused by the channel bits in register 0x05.
why is there a '1' in bit 1. I guess it can't be used and so the range is
00000010 - 2400MHz
00000011 - 2401MHz ...
Dear,
I am trying to test nRF52840 Preview DK.
Is there any method to test bluetooth 5.0 feature or spec?
Especially on speed and distance.
Thank you in advance!
Dear Madam/Sir,
I'm working with SDK14.2, softdevice5.0.0-2alpha, s140, and nRF52840 through the DevKit.
I'm recurring to the fstorage API to read/write/erase flash while...
Does enabling POFCON on nRF51822 lead to any increase in power consumption?
If yes then what is the value?
I struggle to find any information in Reference Manual or Product...
Hi
i am new with nr24L01 module , i am currently trying to configure them but , i am not able to read the RF_CH register just after write into it ? so i don't know if the...
Hello. I am using ble_app_uart from sdk14.2. I use pca100401, softdevice s132.
Advertising is generated using timer RTC. Board advertises and stops advertising without errors...
Here is our requirement.
We want to have four transmitters based on nRF2460 and more than 100 receivers. It means there will be four broadcasts.
Each receiver should...
Hi DevZone,
I am working on a project using nRF52840 preview DK and Arduino CAN Bus shield. I modified source code base on some Git Projects. It seems the SPI initialization...
Hi everyone!
I want to implement SPI with "ble_app_beacon" example with the following hw/sw.
DK : nrf52832
SDK : nRF5_SDK_14.2.0_17b948a
IDE : Segger Studio 3.34...
Recently,I use the SDK14 to develop the project,the initial project is in the content "SDK14/examples/peripheral/twi_scanner/pca10056",
Then and the spi example in the content...
