Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I am trying to interface MCP2515 with nrf51-dk. MCP2515 talks over SPI, so I have taken SPI_master as my base code. I have used MCP with arduino, so I thought it would...
Hi DevZone,
I am Nordic beginner, I am using the Nordic SDK example code for my current project. Before using Nordic DK, I was using Arduino for this project.
There are...
I'm trying to enable the S140 softdevice on my nrf52840-PDK from NuttX. When I call sd_softdevice_enable(), it returns NRF_ERROR_INVALID_FLAGS, which is not one of the documented...
I hope, operating BLE 5.0 at low data rate will give us longer range in open space. So in an environment like a football field, where each player will have 5.0 operating devices...
Hello,
I tried to add the code of the bluetooth tutorial called "Bluetooth low energy Characteristics, a beginner's tutorial", with a code that measures the delay of two...
Hi
I am working on a design using an nRF24L01+ in a circuit also consisting of an ATMEGA microcontroller and a H-bridge motor driver driving a brushed DC motor. The whole...
hi all!
I would like to ask the DCDC and LDO two modes of choice. My product is a watch, it uses the cr2032 battery dropped to 2.5v by an external LDO to 52832 power supply...
Hi,
I am using nRF52832 development kit PCA10040 V1.2.1 2017:38. I am able to successfully run nRF_Examples\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral...
hi,
I am using PCA10040 v0.9.0 Nrf 51 DK.
In schematic I am not getting connection for programming connectio n .In sheet 4 of 5 at the USB Connector connection signal...
Hi,
I m trying to develop an linux-application running on node.js to communicate with a nrf52 device. I m using the noble-module ( noble ) and a usb bluetooth-dongle. ...
Hi,
Is it possible to connect nRF905 to nRF51822 via SPI, add ShockBurst code nRF51822 and then use alternately/simultaneously Sub GHz and Bluetooth communication?
I'm...
Is there nRF Connect or similar program that enables development of BLE applications for Windows 10 (using native BLE API - ideally universal windows platform)?
At a connection the call function app_error_fault_handler()
with parameters
m_error_data.fault_id = 0x01 m_error_data.pc = 0x14DBE m_error_data.error_info = 0x0
Is not...
I'm trying to configure UART functionality in my program, and in the event handler under APP_UART_DATA_READY I'm missing bytes that I should normally have received. The code...
Hi,
Is possible to program the nRF52832 with a target voltage between 1.7V to 3.3V? I'm thinking to power supply the MCU with a pair of AA batteries in series.
Thanks...
