Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Noted that the new V15 SDK for IAR does not have linker config file set correctly on ble_app_blinky_pca10040e_s112 project. The .intvec start location was set to 0x19000 and...
Hi all ,
i'm using nRF51 DK ,im getting issue while program downloading on flash .Program compiled correctly(no any error) even it show flash downloaded but the application...
Hi There,
I have been looking into how to connec my QSPI NOR Flash to the NRF52840.
I have notivced a discrepancy between the comment in the Table 3. of the OPS and the...
Hi,
I have a peripheral which sends data to the central and from central i n eed data to be send to Mobile App
is it possibe to do and how???
or any other ideas you...
I am using Keil 5.24.2
I already downloaded and compiled with build_all the micro_ecc. Having no issues here.
According to the error, and what I read in another thread...
I have been investigating the possibility of using the QSPI external flash peripheral on our NRF chip. After doing a typical qspi read command, the external flash chip would...
Hi,
when i make a connection to my device i get 4 `BLE_GAP_EVT_CONN_PARAM_UPDATE`.
If i make an action of read or write when update event occures i get a duplicated read...
Greetings,
Here's an implementation of controlling the color of a RGB LED with a TIMER of nRF51. It works well most of the time, although it inverts polarity kind of randomly...
Hello,
I am using a Nrf52382 custom board and want to know the Vbattery so I used below code
#define MIN_BATTERY_ADC_VALUE (int16_t)11295 //(min_voltage_on_analog_pin...
Hi,
We have developing ble mesh network using nRF52 mesh sdk is 1.0.1. We have large amount of sensor data it near about 24-25 kb and want to send this data to other node...
I have an application that has been built using Arduino boards and shields for prototyping, and software developed using their IDE...all works fine.
The device comprises...
Hi all,
I am trying to use the SAADC to measure battery level. I have a rechargable lithium battery connected to my customed PCB with a NRF52832. The rechargable battery...
Hello. I have as question about the sd_ble_gatts_hvx. According to the API documents, the call to sd_ble_gatts_hvx will return NRF_ERROR_FORBIDDEN in the following situation...
Utilizing two nrf52832 dev kits, both flashed with v6 of the SD and using V15 of the sdk.
Using two examples from the SDK, the ble_peripheral/ble_app_rscs and a slightly...