Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
Can I use an external edge-triggered (negative edge) interrupt (on a GPIO pin) to trigger an I2C write via PPI? If so, do the I2C registers need to be reloaded each time?...
I'm having trouble using an external j-link probe (J-Link plus compact) with the nRF52840-DK with Segger Embedded Studio. I am powering the DK from USB (Sw9 VDD) , using the...
Hi Great QA team:
Our clients are studying for the details of 52833. And they'd like to know the maximum external draw current through VDD at high voltage mode.
It's clearly...
Hi,
I am testing the ble blinky example as it is from SDK v16.0.0. I am seeing a good amount of time(~340ms) from reset(pin reset) to advertise the first packet. I am keen...
So for this what I am trying to do is-
result = ((float_t)0x3F4040A3); NRF_LOG_INFO("My float number" NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(result));
But this is...
Hi
I have a strange phenomenon when using ANT proximity function.
Configuration: nRF52840, SDK15.2.0, softdevice S340 v6.1.1
The following initialization function of...
I've been using the USB HID Composite example along with the advice from this thread https://devzone.nordicsemi.com/f/nordic-q-a/38271/writing-words-to-usb-composite-keyboard...
Good day
I'm trying to run the ANT IO demo using two nRF52840 DKs. In order to do that I am trying to migrate the example from softdevice s212 to s340. I am currently using...
hi,
i want to connect 18 peripherals to a central. if iam changing NRF_SDH_BLE_CENTRAL_LINK_COUNT and NRF_SDH_BLE_TOTAL_LINK_COUNT more than 8, all peripherals stop pairing...
Hi,
usbd_cdc_acm project implemented UART over usb, which is great. However it cannot send bytes from PC to DK board, only DK board back to PC.
In order to implement sending...
I use the SPIM to access a nand flash memory device. There are times, when I need to "free" the SPI bus allocated by the nRF52840, so that another CPU can access the memory...
I have been closely following this thread ( https://devzone.nordicsemi.com/f/nordic-q-a/52689/nrf9160-lte-sensor-gateway-on-thingy-91/217018 ) to provide support for the LTE...
Hello all,
I am using the NRF52810 board with SDK 14.2
I wanted to convert pca10040 to pca10040e file of buttonless dfu and secure bootloader .
I have gone through this...
Hi, I can read data with my laptop BLE as below.
Could anyone tell me where can I find the data layout doc? I want to figure out the data layout and dimension.
Thanks...
I've been having several issues with the nRF52840 so far:
Issue 1:
When trying to flash an nRF52840 with NCP firmware using a Segger JLink, I connected the SWDIO and...
