Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
I am Planning to Implement Card sniffing with NFC Front Chip !
Can I Utilize Comparator for card presence detection system senses the card by measuring the decay time of...
Hi
The slave select (ss) pin during the spi communication is always low even when i make it high to release the spi bus. It looks to me that I'm not actually controlling...
Hi All,
I got 66uA current consumption in sleep mode and trying to reduce it further to few uA. I have disabled the serial interface and still wondering if there is anyother...
Hello All,
I am working on the nrf52810 module.
I am using sdk 15.3 with softdevice 6.1.1. (IDE segger)
Issue-
1. I am giving the Advertising name as " TEST_01 ...
Hi everyone,
this is my first question in this blog.
I am trying to use the library pc-ble-driver-py in order to interact with a DevKit (in which an example code is implemented...
Hello!
I want to use a long range and buttonless bootloader in nrf52811. S140 cannot be used for this task, because S140 use more then 150KB of flash.
Is it planned to...
I need to download nRF Sniffer v2.x, but the link is not valid, please send me a valid link
Old unavailable address: https://www.nordicsemi.com/Software-and-Tools/Development...
Hello,
I have to send hardcoded AT commands on button press on nRF9160dk. So for that, first I did program for button press. It is working fine. Then I did simple_at program...
Hi,
SDK: nRF5_SDK_00.11.00 ; S132 SoftDevice v2.0.0
I am working now to migrate my application from DM to PM (in order to better handle pairing&bonding).
Sometimes the...
Hi team, there is nRF52840 connected to STM32 via UART, the goal is to receive STM32 firmware over BLE (using nRF52840) and send the firmware to STM32 via UART.
My goal...
Hi!
I am realizing a comunication between a serial device and the nRF52832 through UART; i set PIN 5 for TX and PIN 10 for RX (after set PIN 10 for GPIO use) and i don...
Hi
I am planning to use Zephyr Rtos on a Telit Module (BlueMod-S42) based on the nRf52832 SOC.
As we are making both Client and Server application, the question has 2...
I was using a sample code from here which was posted by Jørgen Holmefjord at the link: https://devzone.nordicsemi.com/f/nordic-q-a/43750/to-display-uuid-major-minor-values...
