Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I have problems getting the beacon example in the new mesh SDK v0.10.0 working.
I invoke cmake with this command:
cmake -DTOOLCHAIN=gccarmemb -DPLATFORM=nrf51422_xxAC...
Hi there~. This is Matthew! I saw a thread explaining that the production variants of the nRF52840 will first be available Q4 2017 at this link .
I was planning for BLE...
Hi,
I had a difficult problem.
First, S110 & SDK9
ble_stack_init () is the source.
static void ble_stack_init(void)
{
uint32_t err_code;
// Initialize the...
Hi. I'm using nRF51822 as Peripheral.
To init the service for example "NUS", i have to call NUS_BASE_UUID as below..
#define NUS_BASE_UUID {{0x9E, 0xCA, 0xDC, 0x24, 0x0E...
Hey guys,
From what I understand, the minimum connection interval on say, an iPhone, is 20ms. Also, you can send up to 6 packets of 20 bytes within a connection interval...
I have established a ble connection between two dk boards, the code I based on is the ble_app_uart_c and ble_app_uart, and try to detect some rising edge delivered from the...
It's kind of relative question with my previous question.
"When smartphone range is shorter than a peripheral(nRF5X), is there any way to receive an advertisement from the...
Hi all, I tested the example: Experimental: LE Secure Connections Multirole Example with my smartphone and it is working fine, but when I tried use LESC on my peripheral device...
I can't open a com port after starting the nRF Connect app. This happens in Windows (native) and also a Linux virtual host with the com port passed through. I'm using a nRF51...
I found strange behavior when using back-to-back packet transmission.
Configuration of PTX/PRX is:
No Auto-ACK (disabled)
CRC 2 bytes
Packet length 13 bytes
Addr...
I have the blinky examples working, but have not been able to get any example code using any gpio input to work. they compile fine but the buttons done seem to work. I'm using...
Hello,
I'm using the sample project from this post .
Following the steps and using nRF52DK, one for server and one for client. I've modified the server count from 3...
Hi all , I has 3 board : 1 board central connect with 2 board peripheral . I want to send string from peripheral 1 to central , then from central to peripheral 2 . Please...
Hi All,
We have a data logging application, where our typical data packet is small -- roughly 20 bytes. I've been experimenting with FDS for storage, with one record for...
