I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I'm working on nrF52832 with two different Android device : Samsung Galaxy note 3 neo and HTC ONE M8.
My test :
Central side ( smartphone ) : each 200 ms...
Hi!
Does Nordic have plans to include any API functionality for choosing an initial scan channel in sequence of jumping over 37, 38, 39 channels?
Currently (SoftDevice...
Hello Nordic,
I tried to debug my board using the JTAG port (P12) on the nRF6310 motherboard. But it's not possible to flash the chip in Keil. I got the error: "Error:...
I use nrf51 DK (PCA 10028) like hardware for sniffer.
I download sniffer software 1.0.1 and flash the dk with help of nRFgo Studio.
I start sniffer.exe and after unplug...
Hi, I'm developing an application for the nRF52832 using mbed and the S132 SoftDevice. Since it appears that the SoftDevice requires exclusive use of Timer0 and mbed uses...
Hi,
I am having 1 central and 2 peripherals. I use ble_app_hrs as the base for both. Sometimes, I dont get the BLE_DB_DISCOVERY_COMPLETE even after I get the BLE_GAP_EVT_CONNECTED...
Hi,
I had some erratic results when I hook these devices via SPI, using a level shifter (e.g. TXB0104) to protect the nRF52. When I look at the schematic for the nRF52...
How I can pairing via NFC with phone? I want that pairing was with a password. I used for exaple project "experimental_ble_nfc_pairing_reference". I used SDK 14 and SoftDevice...
Hi,
I've couple of Nordic Thingy 52.
I was able to connect to these using my Samsung A5 2017 running Marshmallow and see the various sensor readings.
After an OS update...
I am in the process of porting my code from SDK13.0 to 14.0 in order to use s332 v5.0
I can compile and run my application. While it's running, I can see that it is sending...
We are using this device and we seem to have an issue reading from P0.20.
I know this is a dual purpose pin. We have programmed it for input with pullup. We have it attached...
I am currently porting my project from SDK13.0 to 14.0 so I can use s332 v5.0.0.
I receive warnings when compiling
.\_build\nrf52_firmware.axf: Warning: L6330W: Undefined...
I would like to know if it's possible to pair two NRF52832 together using NFC. NOT an android phone to an NRF52, but a central NRF52 standalone connect to a peripheral NRF52...
Hello,
I am using nrf52832 with SDK12 with gcc compiler. I have extended the ble_app_template example with 2 services.
I have 1 timer interrupt using RTC(100 ms) and...
I've been noticing lately when running debugging on my code, a few minutes in it loses connection and says No Source Available for "0x01e054". I'm sure how to even figure...
