I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to receive a string of 708 characters via BLE. As BLE cap a maximum of 20 bytes per transmission, at the mobile app side I break the data to be send every 20 characters...
Hi All.
I wanna to continue Advertising during peripheral connection due connectable ADV prohibited if Peripheral connection established for nRF52840.
Is it possible to...
I'm trying to print a 20 byte array over uart before sending it on BLE. My array contains:
{0x34, 0x12, 0x00, 0xFF, 0x00, 0xFF, ..., 0x00, 0xFF}
However when I try...
Hi, i am actually working on a smart lock and i want to implement an Automatic Unlock.
This functionnality can be really useful, because the door unlock even if your smartphone...
Does the ACL peripheral protect flash from Read/Write/Erase of CPU and all peripherals? or just CPU? or do some peripherals have a privileged access? (such as the CryptoCell...
Hello,
I'm working on a project that needs sha1 hash functionality and I found this thread about the integration of openssl hmac lib:
devzone.nordicsemi.com/.../
...
Hi,
I have been working with Bluetooth mesh. The test I have been performing repeatedly polls a single node and measures the RSSI (as measured from p_message->meta_data...
Hi,
I purchased Thingy:52 I want to develop ble mesh n/w application on Thingy:52.is it possible that I get any sort of support from you in this context.
I'm trying to run the Thread DFU examples on nRF52840, unfortunately I can't get them to work. On the client, I got the bootloader set up and ready, with the client application...
Hello!
I don't quite understand how to properly link NFC tag library (nfc_t2t_lib_gcc.a) to Segger Embedded Studio Project.
Steps I did:
Add nfc_t2t_lib_gcc.a...
Hi Nordic
Do you have a message sequence chart for how to do a Gatt Client Write with response? I can only find a GATTC Characteristic Value Write Without Response in the...
We are using the nRF6707 power profiler kit to measure our EVB’s current consumption in advertising mode. We use the example app ble_app_pwr_profiling. The only change is...
Hi,
Is there any example of adc (saadc) and uart throw ble?
I want to take same measurements from fotoresistor and send data via ble_uart i found same example but no...
I have a problem in selecting inductor(L1). In NRF52832 IC datasheet, mentioned specifications of inductor L1 are: 3.9nH, 0402 high-frequency chip inductor. What should be...
