I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have two characteristics inside a same service - one characteristics notifies periodically and another on demand. I call sd_ble_gatts_hvx to send notifications with appropriate...
Hi all,
I got strange behavior: when I disable the SoftDevice (nRF52832, S132 V3.0, SDK 12.2) seem that ALL the RTCs, not just the one used by the SD, are stopped, and...
Hi.
I got the ble_app_beacon example to enter System On low-power mode (and operate in the 1 to 2 microamp range except when broadcasting). And I also got that example...
Rather than using previous timeslot examples for esb and ble multiprotcol, can we manaully switch between both protocol, what kind of process need to switch from ble to esb...
Hello,
I am building a project that required pwm drivers and BLE UART. I started by using peripheral ble uart example in SDK 12 and adding the pwm driver source file from...
I'm in need of some help with connecting to the Thingy 52 when using Windows 10, in this case Windows 10 Pro. I've tried Google Chrome and Opera.
If that helps, I have...
Hi,
I'm using sdk14.2 peripheral examples fds and fstorage in an attempt to test flash storage persistance (with softdevice present).
The two examples are quite intuitive...
Is there any way to invert the PWM behaviour easily? I'm trying to develop firmware that will run on the DK52 (LED active high) and my custom board (LED active low).
I...
Like it says in the title. I'm working on an embedded application where lifetime is pretty important, so I'm trying to get power consumption down as low as possible. I don...
I have Rx sensitivity issues when DCDC is enabled
The 52832 datasheet shows these connection:
DCC: 10 uH,
DEC4: 15 nH
When switching both inductors I get better sensitivity...
Hi, I am have been using PPI to control SPI transfer in response to a GPIO interrupt.
The PPI initiated SPI transfer that reads an external device's register A and I would...
while the ble_uart example is a great resource of information, i have a need to completely separate the ble nus data in / out from the hw uart code
using sdk 14.2.0
...
Hi everyone,
So I've this arduino code that utilizes the I2C library and made some convertions to it to work with the nrf52832 in the segger embedded studio and when debugging...
Hello, I'm trying to migrate an Atmel project to nrf51822 chip.
Now, in the original project there were 2 CB arrays registered, one dealing iwth GATT one with GAP:
a...
