Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
i changed the code to send environment data over ble_nus service and it was worked
so i tried to send motion sensor data over ble_nus service and i changed code but no data...
Im developing a mesh network based on a custom board using the nRF52832.
I fine with sending some bytes over mesh . But now i want so send more bytes over mesh using Instaburst...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on setting Tx power...
Today ,I look up the SDK revisions，found that SoftDevice S130 V2.0.0 support NRF51822 V3.Now my production use S130 V1.0.0,but Chip revision unknow(N51822 QFACA2 1921DC).Is...
I have an application based on ble_app_hrs_freertos from SDK14.
Sometimes the application will not start advertising. When this happens, it does not help to power-cycle device...
Hello, I start in programming on nrf9160 DK. I followed the tutorial "getting started part 2" (https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hello,
Good Day!!
My question regarding the reset functionality of the device.
Reset the device on the short press of the reset button and on Long press (for example...
Requirements:
Transmit an advertising packet that can be received by a native IOS App & a native Android App.
Using an nRF52810, I need to set it to Advertising (non-con...
hi,
The data is sent to the app by sd_ble_gatts_hvx(), but the data obtained by this app is wrong.
When salve sends a byte, the data obtained by the app is always 0,but...
When I download \nRFready Smart Remote 3 nRF52 v1.2.1alpha\nRF5x SDK-SR3\examples\ble_peripheral\smart_remote_3_nrf52\Projects\Firmware_nRF52832 to my 52832 device, I can...
Hello everyone,
I am modifying the ble_central_uart example to connect directly with a device using its MAC address. For some reason I don't understand, it doesn't find...
I am getting an NRF_ERROR_INVALID_ADDR when using the SDKv15.2.0 call nrf_sdh_ble_enable() with softdevice s332v6.1.1
The ram start address provided to the function is...
Hello,
I am creating a wearable PCB with the Raytac MDBT4Q-P BLE module, which uses the nRF52832. I need this device to have OTA firmware capability, but I'm finding it...
