I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi Nordic,
Are there any plans to update the BLE Sniffer?
It would be great if all the op codes for logical link control could be added and to fix the malformed packets...
This is the Energy Profile that is shown for the nRF82832 and I am wondering about the RX/ switch parts. I assume these RX phases are for receiving scan requests?
What happens...
Hi,
I have a question regarding DTM in nRF5 SDK v14.2.0.
From what I understand Nordic is making use of the payload type '11' = Vendor Specific and is using the length parameter...
if flash nrf52832_xxaa.hex , board start to blinky
if flash s132_nrf52_5.0.0_softdevice.hex, board seems dead
what happed after flash these two hex files
does these...
Hi Folks,
I am playing with uart ble example described in this link ( devzone.nordicsemi.com/.../).
However, I would like to disable encryption on BLE link. I was trying...
Hi,
I have installed Software backend (micro-ecc) as given in:
infocenter.nordicsemi.com/index.jsp
Compiled example: experimental/ble_app_multirole_lesc --> compilation...
I want to make a BLE peripheral device that only allows connections from authorized mobile apps, and an app that only allows connections from authorized BLE devices. What...
Hi all,
I'm having problem porting some project from Keil to SES since our project use absolute memory location to put some variable that will be share between main application...
Hi,nordics
I failed to find primary service successfully .The sdk version is 10.00 and I reffered to the example is ble_app_uart_c_s120.The pripheral is a gamepad .I can...
Hello there,
I was wondering if there's a known issues page fro SDK 14.0.0 (not alpha).
Issue #1: crypto compile error:
I ran into an issue compiling nrf_crypto.c
...
Hi everyone,
Does anyone have the beginner tutorials about BLE migrated to SDK 14?
I am specially interested in those about services and characteristics:
devzone...
what command did "nRF Connect" do, after I click "YES" ???
Im stranded in this example : “ble_app_alert_notification”
I don't know how to use "nRF Connect"
when I...
Hey Dev Zone!
I'm attempting to flash FW onto the Thingy via the nrf52840 dev board (which includes JLink). I connected P19 header on nrf52840 to P9 on the Thingy. I downloaded...
I am trying to run below 10 uA with code below while GPIO and uart are on. Sleep mode is applied (below 10 uA), and only wakes up when button is pressed (can be higher amps...
I have a micro connected to the PCA10040. I can use flow control with 5=rts, 6=tx, 7=cts, 8=rx.
Are these pins necessary or advisable for hwfc?
thanks,
Richard
