I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hi Nordic,
Are there any plans to update the BLE Sniffer?
It would be great if all the op codes for logical link control could be added and to fix the malformed packets...
This is the Energy Profile that is shown for the nRF82832 and I am wondering about the RX/ switch parts. I assume these RX phases are for receiving scan requests?
What happens...
Hi,
I have a question regarding DTM in nRF5 SDK v14.2.0.
From what I understand Nordic is making use of the payload type '11' = Vendor Specific and is using the length parameter...
if flash nrf52832_xxaa.hex , board start to blinky
if flash s132_nrf52_5.0.0_softdevice.hex, board seems dead
what happed after flash these two hex files
does these...
Hi Folks,
I am playing with uart ble example described in this link ( devzone.nordicsemi.com/.../).
However, I would like to disable encryption on BLE link. I was trying...
Hi,
I have installed Software backend (micro-ecc) as given in:
infocenter.nordicsemi.com/index.jsp
Compiled example: experimental/ble_app_multirole_lesc --> compilation...
I want to make a BLE peripheral device that only allows connections from authorized mobile apps, and an app that only allows connections from authorized BLE devices. What...
Hi all,
I'm having problem porting some project from Keil to SES since our project use absolute memory location to put some variable that will be share between main application...
Hi,nordics
I failed to find primary service successfully .The sdk version is 10.00 and I reffered to the example is ble_app_uart_c_s120.The pripheral is a gamepad .I can...
Hello there,
I was wondering if there's a known issues page fro SDK 14.0.0 (not alpha).
Issue #1: crypto compile error:
I ran into an issue compiling nrf_crypto.c
...
Hi everyone,
Does anyone have the beginner tutorials about BLE migrated to SDK 14?
I am specially interested in those about services and characteristics:
devzone...
what command did "nRF Connect" do, after I click "YES" ???
Im stranded in this example : “ble_app_alert_notification”
I don't know how to use "nRF Connect"
when I...
Hey Dev Zone!
I'm attempting to flash FW onto the Thingy via the nrf52840 dev board (which includes JLink). I connected P19 header on nrf52840 to P9 on the Thingy. I downloaded...
I am trying to run below 10 uA with code below while GPIO and uart are on. Sleep mode is applied (below 10 uA), and only wakes up when button is pressed (can be higher amps...
I have a micro connected to the PCA10040. I can use flow control with 5=rts, 6=tx, 7=cts, 8=rx.
Are these pins necessary or advisable for hwfc?
thanks,
Richard
