Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi,
I use it as a translator for Google, so it may be strange in context. please understand.
I was in big trouble.
I used the nRF51822, S110, and SDK9 in my previous...
Hi. We are attempting to use the Infineon XMC1202 LED shield with our NRF52 device. The XMC1202 has an I2C address of 0x15E, instead of the traditional 7 bit address. We have...
I've tried linking the ESB library (esb_arm.lib) in Eclipse by adding it to my nRF51822 project's Makefile, but I am still getting undefined reference errors during build...
Hi
We are going to use the Taiyo Yuden Evaluation Board - EBSHJNZWZ.
As i understand, the board firmware used the Nortic SoftDevice S132
The question is :
May i...
Hello,
I'm trying to compile an example of nRF52_SDK_1 but I get this error:
make
Makefile:150: Cannot find include folder: ../../../config/receiver_pca10040
Makefile...
Hello,
I've been reading over different examples and questions on the Nordic Developer Zone but still have some questions about multiple SAADC channels.
1 - If I initialized...
I've been developing an application on the nrf51 DK based on the ble uart application and it's been working fine. I've ported it to a custom board running at 1.8V and attached...
Greetings -
I am using (the slightly out-dated) 12.3 SDK with a nRF52840. I'm also using s132 as my softdevice.
As I've been slowly reducing my RTC interrupt frequency...
Hi,
I want to activate readback protection on nRF51822, in a simple project without bootloader without softdevice.
My compiler is GCC and the const uint32_t UICR_RBPCONF...
Hi. I don't understand how to build nrf_drv_saadc.c with gcc. I'm getting this error in the EVT_TO_STR() macro:
Compiling file: nrf_drv_saadc.c
In file included from ...
Hello,
I'm going to use nrf52-ble-image-transfer-demo-master for my application.
But demo used other way with cpp code for configuring nrf52832 interfaces(spi, twi, gpio...
Hello Folks,
Nice to see an active developer community out here! I ran into some issues last night which I hope could be resolved. We procured nRF52840 SoCs and have developed...
Hi all,
i'm new to BLE in general, I found this chip (nrf52832), which suits my uni project.
However, I don't have much knowledge about this technology. therefore, im...
Hi everyone,
I would like to test the capabilities of nRF52840. I understand that it should be capable of higher throughput (x2), increased broadcast capacity (x8), and...
