We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hello Nordic Support Team,
I’m developing a Zigbee-based light switch using a Sleepy End Device (SED) configuration with ZBOSS. I've encountered a critical issue related...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
Hello Guys
I'm currently working on a BLE AoA (Angle of Arrival) application using the nRF52833 Development Kit . I’ve run into some challenges regarding hardware connectivity...
in nRF51822 product specification a maximum absolute rating of 3.9 Volt is reported, while in electrical specification the maximum voltage is 3.6 Volt.
The question is :...
Hi,
I have tried with the nrfjprog tool and I get the following error:
Command:
nrfjprog.exe --eraseall --programs s110_nrf51822_7.1.0_softdevice.hex --program HILO_P_01...
Am trying to setup a module where I need to send the Serial port ( say from printer/peripheral COM)
to a BLE Peripheral/Central Module. Not sure which SOC or combination...
I have a board built which is a tracking device with a GPS and GSM modem. I'm beginning field testing and have been flashing it with a Segger then disconnecting the Segger...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I have used the nrf8002 chip before and love it but now I am trying a different application that requires a bit more smarts. I am trying to design a system that can have an...
I have an nRF51822 board that is running fine for a while. At some point, it runs into an error and calls ble_debug_assert_handler() and goes into an infinite loop. At that...
Hi all,
I am new to nRF51822,now I want to used a simple ble application to send a data,and nRF51822 ble device read this data to control RC servo motor ,for example app...
We are using S130 v0.9 stack,
and when BLE device A is connected as peripheral of iphone
and central of BLE device B at the same time
iPhone --> A ---> B
Device...
Hello,
I am working with the nRF DK trying to read a sensor over I2C. I wrote some code in Keil uVision and I finally could read the sensor. The problem now is, for some...
I encountered a strange problem system reset. My application runs on iOS or android. My device was connected by iPhone 6 plus(128G) with iOS 8.1.2. ANCS was turned on. I have...
Hello Everyone
I want to implement TWI interface in my project.Presently I am using Keil UV5 IDE, PCA10028 Development board and s110 7.1.0 softdevice, along with that...
Hi,
So am new to all this BLE stuff, I have been using the nRF24L01 modules but want to move to the BLE variant, nRF51822.
I am these days figuring out the toolchain...
Hi,
I am developing on a nrf51822 based board using s110 softdevice v. 6.0.0.
In my program I need to change the bluetooth GAP device name in runtime
during connection...
