Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
I see this question asked before, but its 1+ year ago, so trying to see if there is some progress....
We have DFU working between your nrfConnect app and our nrf52840 peripherals...
Hi,
I want to use nrf_crypto_aes_cbc_withpadding example in my own project using uECC backend, Please guide me which files are needed to be required to add in my own project...
I am using SDK 15.3.0 and need to create a single hex file to program the initial batch of our nRF52840 based HW. Currently, I have built the bootloader project (open not...
Hi,
I'm facing some problems in the use of the Logger module when the option NRF_LOG_FILTERS_ENABLED is set in the sdk_config.h file.
I'm working with the nRF5 SDK for...
I'm trying to get LPCOMP working on Zephyr - from my research online I can see no information about this currently so I'd like to find out how to do this.
According to an...
Hi,
The documentation for the nRF52840 (section 6.20.15.9) states that RSSI has a typical accuracy of ±2 dBm. I have measured signal strength at multiple distances, and...
HI,ALL！
I use official routine development NRF51822，nRF51\nRF5_SDK_12.3.0_d7731ad\nRF5_SDK_12.3.0_d7731ad\examples\ble_central\experimental\ble_app_blinky_c\pca10028\s130...
Hi,
My problem is with generating interrupts in lsm6dso relative tilt mode.
I asked it in st community, but I didn´t get any answers.
I'm trying to implement a relative...
Hello,
I couldn't understand the predefined header files for the spi, so I'm building the spi code from scratch.
To build init_spi function, It's clearly mentioned in...
Hi,
We are currently trying to design a system using one of the nrf5 bluetooth chips. However, we are still in the process of designing a functional antenna and need to...
Hi, I am trying to implement an example that support multiple peripherals (HRS & UART). When I get a connection (from either) I get the BLE_GAP_EVT_CONNECTED. How can I differentiate...
What is exact difference between heartbeat and health models?
I know heartbeat can be used to detect node outage, but so can be health message?
So, which one should be...
When starting up the device with the nRF5 SDK 3.2.0 for mesh, even though the model and subscription list state is loaded from flash, it is stored again right afterwards....
To the kind attention of Nordic support team,
I was reading this blog https://www.ericsson.com/en/blog/2017/12/wake-up-radio--a-key-component-of-iot
May I ask if Nordic...
