Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
Iam implementing FATFS with USB mass storage on external flash(QSPI). it already having developed dfu in internal flash
***********build errors******************
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello,
I'm trying to add Wi-Fi OTA functionality to a project I'm currently developing, but I'm having trouble getting it to work properly.
Would it be possible for you...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
I am currently working on interfacing an external flash memory IC (Winbond W25FV series) with the Nordic nRF52832 on my custom board , using the nRF Connect SDK .
However...
Hi I have successfully set up my ARM SPI interface to use the nRF24 chip. At this time I'm trying to establish connection but I'm not sure I under stand the setup for comm...
I'm getting this when im trying to select the device.
when i try to update the firmware nrfgo studio is getting closed
please help me in solving this!!
Let's first compare two pieces code:
This one works:
But this one doesn't:
My problem is that as soon as I try to process received data, some of data is lost. Is...
I am developing with SDK 15.0.0
I want to add NUS service in ble_app_buttonless_dfu example.
All I have done:
1. Add including files and including paths to the project...
This is really a two part question.
1. How do I even refer to pin P1.00? It's clear that pin P0.06 is referred to simply as pin 6, but what is the naming convention for...
Hi,
i try without succes to go into MemoryRentention Timer On sleep mode, and wakeup with the analog comparator activated by AIN1 without sucess. Here is my code, please...
Hello I am using nrf52832. I would like to write a custom ISR for GPIO based interrupt. Are there any examples/documentation i could use to get started on this.?
Dear All,
we use Reference configuration 4 and have connected the DK to our custom PCB. 3.3V of the DK go into VDDH and otherwise only GND and SWDIO/SWCLK are connected...
hi
i downloaded nordic thingy52 FW and i uploaded on my board PCA20020
and that is working correctly but when a i downloaded nRF5_SDK_15.0.0 at first i compile (ble_app_beacon...
Dear Nordic,
i am just testing ble examples in nrf 52840 dongle and also implementing one uart for just testing
TX pin - 1.10
RX pin - 1.13
transmission works fine...
Hi,
I'm referring to -
1. Custom HID over GATT device
2. nRF51422 HID example modification
So for now, I just used the descriptor mentioned in above links. But "hello...
Hello,
The softdevice S132_SDS_v4.1 spécification write that supports 20 connections at the same time.
I would like to know if it's possible to have 1 central and 20 peripherals...
I'm attempting to make cli application to load from after the softdevice and based on a command enable/disable the BLE functionality. Is there any simple way to do this? Are...
Hi,
I am currently trying to use PCA10001 board as master and slave at the same time. Trying to send data from master(SPI0) and receive it using slave (SPIS1).
I have set...
Hi,
Is exist a tool like nRFutil to make DFU from windows with standard BLE ?
I have found this: https://github.com/NordicSemiconductor/pc-ble-driver but I thing it's...
