During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Hi,
I’m streaming high-rate sensor data over BLE with an nRF52840 running NCS v2.9.0.
Data rate: 1 kHz, ≈ 8 400 B/s
Packing: 5 samples → 42-byte packet, pushed...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi Nordic Team,
I recently joined the DevZone and I’m interested in contributing to the blog. I’d like to write technical articles and tutorials related to Nordic products...
Hey guys,
I followed this guide and successfully synchronized the timers from two devices(nRF52 DK). But if I let these two synchronized devices keep running all the time...
Hi,
As stated here :
After manually starting the HFCLK
crystal it will be enabled even though
there are no peripherals requesting
the HFCLK. When no peripherals...
Hi,
I have my 2 nRF51 running with S130 v2.0.1, one is the central and the other peripheral.
I am transmitting audio data between both and want to reduce the current consumption...
Being a person with a poor name memory, I am really frustrated with the nRF SDK's naming conventions. For example, let's take a function
bsp_btn_ble_on_ble_evt()
Is...
We are using nrF52 series in combination with v3.0.0 of the S132 SoftDevice stack. And I want to understand if we have to go through any of the qualification certification...
Hi,
i got a random disconnect and cant find the cause.
I found this post devzone.nordicsemi.com/.../ and tried to folow the procedure.
I have set up breakpoints wherever...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control the onboard led that uses the methods LEDS_ON and...
I am using the nrf52832 with its Development kit to transmit trough UART to the PC a frame with 20 bytes, I have configured the port to 1MBoudRate. I have enable the flow...
I spent some time trying to work out why generating a private/public keypair in my application with the ECC module was failing due to an 'internal error' and had to eventually...
Hi,
In 868 Mhz band NRF905 supports frequencies 862.8Mhz, 868.2Mhz, 868.4Mhz and 868.8Mhz. The datasheet shows mapping of those frequencies to CH_NO.
In India only 865Mhz...
Hi,
I am currently working with two nrf52 boards in a serialized configuration.
I wanted to add the PA and LNA pin toogle on the connectivity chip.
As the gpio can't...
sorry, i tried "Getting started with the nRF5 development kit" tuturial about 3 hour.
but still not working for me.
stock at begining.
I downloaded nRF5 SDK 11
and...
Hello,
We are using nRF52 in serialization mode.
In the nRF52 connectivity chip side, we are using the example 'ble_central_and_peripheral'.
In the application chip,...
I would like to use the nRF52840 for 802.15.4 but it is rather vague in the OPS as to how to do this. I can figure some of it out but not other parts.
It mentions "assisted...
