Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am trying to use the NRF51 soft device with the App_PWM library. I can get both working individually, but when I try to enable both, I can no longer connect to the device...
Hi ,
I am trying to interface SD card with nrf52. For this I am using fatfs example of new 12.0 sdk. I can able to write the data to file but when I am taking the data...
HI,
I followed this link github.com/.../nRF51-ble-bcast-mesh to develop mesh in nRF51822 dongles. i am able to flash the code( nRF51-ble-bcast-mesh/nRF51/examples/BLE_Gateway...
Hello, I am working on characteristics tutorial.(our service.c)
And I succeeded in notifying characteristic from nordic to android.
The methods I used to notify characteristic...
I'm in the process of migrating to SDK 12.2 and I noticed that nfu_dfu_settings.c now includes app_scheduler.h and makes a call to app_schedule_execute().
How do I use...
want to send a float as a value of a characteristic
I have successfully achieved this using the simple way
Below is the example of just two float variables in an array...
Hi,
I have a PCB with a nRF51822 QFAC A1 onboard, and I wrote a firmware with mbed for this PCB in which P0.08 is supposed to be set to 1 during the initialization and...
My company is in the final stages of prototyping and we want to release our first product in the coming year (focusing on European and American markets). The next steps are...
Hi,
Does anyone know if there is a way to achieve 12 bit duty cycle resolution at 25 KHz PWM frequency for 5 channels (individual duty cycle for each channel) using the...
I have one of the new Power Profiler Kits, and it works really well (well done!). The only problem is I can't reprogram the dev kit while it is connected to the Power Profiler...
I have tried to build this by double-click on the .xcworkspace file, in the folder obtained from the downloaded .zip (dated Nov 24, 2016), then "Build + Run". I get 203 errors...
I have modified the template's code so ble_advertising_init should setup manufacturer data, once I have this assignment:
advdata.p_manuf_specific_data = &manuf_data;
...
Hi,
I want to use nRF51422 on ant and ble dual mode.
Does nRF51422 can use sd332 and where has example project
or
The nRF51422 just can use Sd310 only so far.
Than...
Hello,
When line 10 of the below code is executed the system enters the BusFault_Handler, at this point the NVMC register is as followed: Ready = 0x00000001, Config = 0x00000001...
