hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I recently started working with the NRF52840DK,I need to read data from MC3461 accelerometer via I2C and transmit the results over BLE.
nrF52840-DK
SDK v15.0.0
SoftDevice...
Hi,
I'm trying to add a 3rd Primary Service to my application. I have increased NRF_SDH_BLE_VS_UUID_COUNT to 3 in my sdk_config.h accordingly, and as expected when I run...
HI Im trying to reduce the power consumption of my nrf52840 based device. And now I need to read peripheral register in debug mode but cant do it.I guess it is enabling in...
For those who migrate to from SDKv15.0 to SDKv15.2 and still using the old project files will notice a difference that peer manager in SDKv15.2 has replaced using the below...
Hello Sir,
I am controlling nrf24L01P using atmega328p. Here I am using sleep on microcontroller and power down at nrf24l01p. So in this case some times internal Ack receive...
Dear Nordic,
We have a custom board and we just flashing BLE central peripheral example on it's
works fine but when i test its current consumption its shows around 1.5...
Hello everybody,
I need to store some data in the flash for application purposes. I'm using the SD332 and the application goes in the DFU mode with the DFU buttonless service...
I added a SIG general onoff model by modifying nordic mesh SDK example project 'example/light_switch', just modified model ID as below:
client:
#define SIMPLE_ON_OFF_CLIENT_MODEL_ID...
Hello,
I have implemented OTA DFU for Xamarin based on the implementation of Nordic's official library for Android . It works in general, but I'm seeing a bottleneck in...
Hi,
I would like to know how to process DTM test for nRF52840 BLE RF TX power, RX sensitivity ... etc.
If there is any test firmware, tools, command lines and application...
I'm trying to migrate to SDK15.0 (from 14.2) for the nRF52_DK and nRF25840_DK. Using the new nrfx_rng.c driver I'm getting a link error as a few functions can't be found:...
Hi,
I'm using nRF52840 with mesh 2.0.0 and started from the light switch example to build my own application. I have now 2 type of boards master (client+provisionner) and...
Dear Nordic Team,
Thanks for supporting.
currently i am working Single channel scanning with ble_app_uart_c example. In continuous scanning missing beacons. Please support...
Currently, in my application, any iPhone can attempt to read from one of my protected characteristics and initiate the bonding sequence. I have it set to "just works" mode...
