Hi.
We are doing automatic network attaching on nRF9151. This is how the flow looks:
AT%XBANDLOCK=2,...
AT+CFUN=1
AT+COPS=0
We do this until we get registered...
Dear Nordic Engineers
We found a problem on the NRF54H20. When we ran C:\ncs\v3.0.2\nrf\tests\benchmarks\multicore\idle_gpio example, the current tested on the VDDHV of...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hello team,
I am using nrf54l15 dk for the devlopment and want to read the RTC counter to check for how much time my device was in sleep mode.
How to achive this?
Thanks...
Hello, I'm using nrf9151-DK kit and this UDP example: UDP . After compile and flashing I opened both serial monitors (VCOM0, VCOM1) but no output appeared. Could you please...
I am using saadc to periodically sample a voltage (per about 12 seconds). The voltage cannot be shutdown and always is a value neigher zero nor VDD (1.25v, 2.5v, 1.0v, etc...
Hi,
I'm wondering if the DTM mode can be entered over the air interface on nRF bluetooth products, as specified by Core4.2 [Vol2 Part C] 4.7.1 Activation and Deactivation...
Hi,
I am looking for an solution which requires to have an BT dual mode(Smart Ready) SoC. As i require the high data rate of 2.1 and also require support of BLE 4.0.
...
HI ,
I need to interface particle measurement sensor with nrf52832. I am using S132 softdevice and SDK 11.0 for my application. I need to send commands to sensor to take...
Hi,
I feel myself a bit silly...my nRF52840 board was working the last few weeks nicely, it was visible both in nRFgo and Keil. I had the board some time in button cell...
Hello, after downloading my user app using keil, I can't seem to erase the whole chip.
This is what I'm trying to do:
erase the whole chip (nrf52840).
program S140...
Hello, when migrating a project from nrf51 to S140 nrf52840, I got an
"Error: L6218E: Undefined symbol app_error_fault_handler (referred from softdevice_handler.o)."
...
Hi,
I am quite a beginner about nrf51822. I understand that I can get RSSI during advertise mode before pairing. But I am not sure I can get RSSI after pairing. Can I get...
Hi, everyone.
Now I have found some posts about the development enviroment on Mac OS X. But none of them describes clearly how to setup the development enviroment with an...
We are trying to get serial bootloader (DFU) working. I compiled a debug version of the experimental_bootloader_secure_serial in SDK13.0.0 to see what really happens there...
Hello,
I am successfully using the following code:
float f = 23.50
char buffer[10];
sprintf(buffer, "Float = %f\n", f);
SEGGER_RTT_WriteString(0, buffer);
I...
Can nRF51 be BLE connected while it's on sleep mode? (connected by other device as Peripheral mode)
I thought, to be connected as peripheral mode, It must be advertising...
Dear Nordic Team,
We have a customer that would like us to extend an C# desktop application to use serial over BLE. What is the best dongle firmware and Windows driver...
