Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
SDK: nRF5_SDK_11.0.0
Softdevice: s132_nrf52_2.0.0_softdevice
project:examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm4
I have some questions about bonding...
Hallo,
I try to port some existing BLE application from SDK 12.2 to SDK 14 that used the S132 Softdevice.
With 12.2 it was possible to configure bandwidth requirments...
Would it be possible to use BLE for a sensor network with aprox. 40 battery peripherals measuring a float at 100hz? 50hz? For one central unit, or how many if needed.. The...
Hi,
One of my pca10040 stays on bootloader mode.
I have tryed copying J-Link OB-SAM3U128-V2-NordicSemi 160212.bin file on the bootloader drive but it stays the same. ...
Hi Everyone,
I just purchased an nRF52840 PDK and I am trying to program it via nRFgo. I erased the flash, selected the latest s140_nrf52840_5.0.0-3.alpha_softdevice.hex...
Hello,
My team and I are experiencing a problem with our custom DFU Bootloader, which is based on the Experimental Bootloader Secure Serial example (SDK 13), running in...
Hi,
My SDK version is 13.0 and my problem is when I run the examples\ble_peripheral\experimental_ble_app_buttonless_dfu project the 52DK seems ok but when I use the DFU in...
Hello:
I am setting up my nRF52840 development board to work with the S140 softdevice on Segger Embedded Studio; however, I am running into issues with the flash_placement...
Hello,
I've seen some conversations around the forum for applications that must share the same ID. My application must share SPIMO and TWIMO (ID 3, base addresss 0x40003000...
Hello,
I want to make beacon with my uuids. I am referring to code ble_app_beacon code from sdk 12.2.2
I have made changes according to my requirements in my code.
I am...
Hi, we downloaded the latest version of the sniffer 1.0.1 (today).
We tried that but we could not get it to work reliably?
The application sees the device, we select and...
I am using the nrf51822 with a latching circuit as shown controlled by P0.05 pin.
I am using the following code SDK 10.0 S110 softdevice to Power ON the circuit (PowerPin...
I've merged serial dfu with ble dfu project refering to this post .
I'm getting linker errors stating no space in execution region in .ANY sector...
What could be the...